ITT Goulds Pumps 3175 Скачать руководство пользователя страница 76

Страница: 76 / 87

Shaft sleeve (if any).

Ball bearings - one of each.

Shaft nut (if any).

Bearing locknut and washer (if any).

8.2 Instructions for Ordering Spare Parts

Repair orders will be handled with the minimum of delay if the following directions are followed:

Give Model No., size of the pump and serial number. These can all be obtained from the name-
plate.

Write plainly the names, part numbers and materials of the parts required. These names and
numbers should agree with those on the

8.3 Parts List on page 74

Give the number of parts required.

Give complete shipping instructions.

8.3 Parts List

Table 7: Construction details

Group S

Group M

Group L

3x6-14

3x8-14

4x6-14

4x10-1

44x6-18

4x10-1

86x8-14

6x12-1

46x8-18

6x12-1

86x8-22

6x12-2

28x10-1

48x14-1

48x10-1

88x14-1

88x10-1

8H8x14-1

8H8x10-2

28x14-2

210x12-

1810x16-

1810x12-

2210x16-

2212x14-

1812x18-

1812x14-

2212x18-

2214x14-

1814x20-

1814x14-

2214x20-

2218x18-

Gen-

eral

Net wgt.
bronze fit-
ted bare
pump w/
suction
piece

850 925

105

110

152

170

155

160

172

180

190

205

200

235

212

280

4500

Min. casing
thickness
C.I.
bronze

9/16 19/3

21/3

23/3

12/1

11/1

3/4 13/1

7/8 7/8 15/1

15/1

31/3

1-1/

1-1/4

Min. casing
thickness
steel

7/16 1/2 17/3

17/3

9/16 21/3

9/16 19/3

5/8 11/1

11/1

3/4 3/4 3/4 3/4 12/1

1-1/1
6

Max. dia.
solids

1-1/

1-3/

2-7/

1-5/

3-3/

2-3/

2-1/

2-3/

2-7/

2-1/

1-5/

2-1/

Pressure

limits

Max. work-
ing pres-
sure - PSIG

Max. test
pressure -
PSIG

See Pressure - Temperature Chart

150% of maximum working pressure at 100°F

Temp.

limits

Max liquid
temp. oil
lube with-
out cooling

Max liquid
temp. oil
lube w/
frame cool-
ing

250°F

350°F for C.I.

450°F for Steel

250°F

350°F for C.I., 450F for Steel

250°F

350°F for C.I., 450F for Steel

250°F

8.2 Instructions for Ordering Spare Parts

3175 Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps 3175
























































































Результаты поиска

Содержание Goulds Pumps 3175

Отзывы:

Похожие инструкции для Goulds Pumps 3175

Бренды по названию

Популярные бренды

ITT Goulds Pumps 3175, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps 3175

Отзывы:

Похожие инструкции для Goulds Pumps 3175

Бренды по названию

Популярные бренды