ITT Goulds Pumps 3175 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 87

background image

Table 6: Frame Adapter to Casing Bolts Torque Specifications

Casing Size

Torque, N-m | ft-lbs

12 inch

91 | 67

14 inch

244 | 180

18 inch

201 | 148

22 inch

233 | 172

28 inch

499 | 368

23. Install pedestal hold-down bolts. Frame pedestal is not to be flush with bedplate. Clearance of 1/4"

is normal. Install shims under pedestal before tightening.

24. Set impeller clearance as outlined in

6.3 Impeller Clearance Adjustment on page 53

. Clearance be-

tween impeller and sideplate should be set at 0.381mm | 0.015" to maintain optimum efficiency.
Overall travel must be 1.499mm to 2.159mm | 0.059" to 0.085" dependent on tolerances. If not,
check casing gasket to be sure it is 1.588mm | 1/16" thick.

25. If unit requires stuffing box packing, refer to

5.4 Stuffing Box Packing on page 33

and pack as di-

rected. Refer also to

6.9 Stuffing Box on page 68

for alternate methods of packing.

26. Replace auxiliary piping.
27. Follow procedures outlined in this manual for preparation and operation of the unit.

NOTICE:

Pay particular attention to instructions concerning alignment and lubrication.

6.8 Set the Mechanical Seals

WARNING:

The mechanical seal used in an ATEX classified environment must be properly certified.

CAUTION:

Running a mechanical seal dry, even for a few seconds, can cause seal failure and physical
injury. Never operate the pump without liquid supplied to the mechanical seal.

1.

With the bearing frame-shaft assembly completed, carefully slide the gland-stationary seat assem-
bly, with gaskets in place on the shaft. Install shaft sleeve.

2.

Carefully slide the stuffing box cover over the sleeve and bolt to the bearing frame.

3.

The following method may be employed to determine the correct positioning of the rotary portion of
the mechanical seal:

a) Scribe the shaft sleeve at the face of the stuffing box.

6.8 Set the Mechanical Seals

3175 Installation, Operation and Maintenance Instructions

67

«
...
67
68
69
70
71
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Altherma 3 R F+W

Бренд: Daikin Страницы: 20

Бренд: Danfoss Страницы: 26

Бренд: Calpeda Страницы: 80

Бренд: Danfoss Страницы: 24

Бренд: vacuubrand Страницы: 76

Raypak Delta Limited 399B

Бренд: Rheem Страницы: 67

Craftsman 390.269451

Бренд: Sears Страницы: 8

ROYTRONIC A Series

Бренд: LMI Страницы: 36

Бренд: Sicce Страницы: 24

Бренд: Pfeiffer Vacuum Страницы: 68

Altherma 3 M Series

Бренд: Daikin Страницы: 24

Бренд: F.F. Group Страницы: 28

DHH 12 Si control

Бренд: STIEBEL ELTRON Страницы: 168

Krystal Clear SF90220T

Бренд: Intex Страницы: 112

Point-of-Use Drinking Water System

Бренд: R-Can Страницы: 12

Blue Diamond MaxiBlue

Бренд: Charles Austen Страницы: 20

Бренд: Carrier Страницы: 36

Бренд: Laars Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды