ITT Goulds Pumps 3175 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 87

background image

1. Shaft

2. Sleeve

3. Scribe

4. Stuffing box

Figure 68: Shaft sleeve

b) Unbolt and remove the stuffing box cover. Remove sleeve. Lightly lubricate the rotary portion of

the seal and slide onto the sleeve.

c)

Compress the rotary to the correct "working length". Refer to the seal manufacturer's drawing
for correct dimensions. Tighten set screws.

6.9 Stuffing Box

WARNING:

Packed stuffing boxes are not allowed in an ATEX-classified environment.

The standard stuffing box cover has four pipe taps for sealing or flushing liquid to the packing or mechan-
ical seal. Two are used for in and out connections to the throat of the stuffing box for paper stock serv-
ices with the lantern ring positioned next to the stuffing box throat bushing. Two are alternately used for
evaporator or chemical services as in and out connections. The image below shows a stuffing box and
location of holes, and the holes used for evaporator service and paper stock service.

6.9 Stuffing Box

68

3175 Installation, Operation and Maintenance Instructions

«
...
68
69
70
71
72
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: TANKLESS Страницы: 72

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Бренд: AL-KO Страницы: 144

Бренд: Acquaer Страницы: 12

Бренд: T.I.P. Страницы: 120

Бренд: Payne Страницы: 4

Бренд: SPX Страницы: 28

Бренд: Watts Страницы: 24

Бренд: Wilo Страницы: 132

Elmo Rietschle VLV 100-2

Бренд: Gardner Denver Страницы: 16

Бренд: Little Giant Страницы: 24

Бренд: Oasis Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды