Instramed CardioMax Скачать руководство пользователя страница 182

Страница: 182 / 205

Troubleshooting

182

Symptom

Probable cause

Probable solution

The CardioMax does not turn on.

There is no electricity.

- Check connections: the CardioMax/Power

Cable/Plug.

Does not select energy > 50 J.

Adult pads identification.

- Check if is adult pads are connected to the

equipment and if adult electrodes are properly

connected.

Does not deliver shock.

Impedance measuring.

- Check the graph bar for the patient’s

impedance indication.

Does not capture ECG via

electrodes.

Lead selection.

- Select a lead other than the “pads” lead.

No tracing.

Unstable since last

shutdown.

- Restore initial configuration.

Low battery autonomy.

Defective battery.

- Turn off battery.

No QRS audio indication.

BEEP volume.

- Turn on BEEP’s volume in the configuration

menu.

No alarm sound indications.

Operation mode.

- Alarm indications are only active in the monitor

mode.

No SpO

curve.

SpO

curve turned off.

- Turn on SpO

curve in Waveform setup.

Pacemaker does not start.

Multifunction/Adhesive

pads.

- Check if multifunction pads are connected.

- Check if there is a “bad contact” message.

- Check gel in multifunction pads.

Does not print .

No paper in the printer.

- Check if there is paper in the printer.

- Check if paper is positioned properly.

Printer makes noises and does

not print.

Too much paper on roll.

- Change roll’s size.

Содержание CardioMax














































































































































































































Результаты поиска

Содержание CardioMax

Отзывы:

Бренды по названию

Популярные бренды

Instramed CardioMax, Руководство пользователя

Результаты поиска

Содержание CardioMax

Отзывы:

Бренды по названию

Популярные бренды