Instramed CardioMax Скачать руководство пользователя страница 131

Страница: 131 / 205

Event and data storage

Data storage

The CardioMax creates an event list for each patient observing the following criteria:

Automatically

- if CardioMax stays turned off for 30 seconds more.

Manually

- via the events setup menu.

The quantity of events the equipment can store will vary according to how long each

patient has used the equipment and the type of therapy used. The CardioMax has a

2 Mb memory.
The last two hours of continuous ECG will be stored in the equipment’s memory.

ATTENTION: Whenever the internal memory capacity reaches its limits,

events prior to 100 will be replaced with new information.
CardioMax does not store patient´s personal data, and does not allow the

entrance of external data.
The CardioMax does not record occurrences of ALARM CONDITIONS.

Events stored

The CardioMax stores date, time, heart frequency and saturation of the following

events:
•  Pads change.
•  Charge values.
•  Number of shocks.
•  Turn equipment on/off.
•  Loose electrode/bad contact in

the pads.

•  Failure in module initialization.
•  Functional test stimulation.
•  Synchronism.
•  Operation mode (monitor,

pacemaker, monitoring).

• Stimulation - pacemaker on/off.
• Turning on the "pause audio"

button.

•  Shock failure.
•  Internal discharge.
•  “Event setting” key activation.
•  Printing.
•  Low battery/equipment turning

off.

• Pacemaker stimulus change.

131

Содержание CardioMax














































































































































































































Результаты поиска

Содержание CardioMax

Отзывы:

Бренды по названию

Популярные бренды

Instramed CardioMax, Руководство пользователя

Результаты поиска

Содержание CardioMax

Отзывы:

Бренды по названию

Популярные бренды