IEMCA KID 80 IV Touch Скачать руководство пользователя страница 5

Страница: 5 / 122

INDEX

1 BASIC

INFORMATION

KID 80 SIV ..................................................................................... 1

1.1 Control

description

.............................................................................................................. 3

INFORMATION FOR USE KID 80 SIV ................................................................................ 1

2.1

AUTOMATIC CYCLE START................................................................................................ 2

2.2 OFFSET

PROCEDURE (ADJUSTMENT) ............................................................................. 3

2.3

CYCLE PERFORMING MODE IN THE STEP-BY-STEP FUNCTION ................................... 4

2.4

BAR FEEDER STOP ............................................................................................................. 5

2.5 0-AXIS

PROCEDURE (MANUAL MODE) ............................................................................. 6

2.6 OPERATOR

PARAMETERS: OPERATION MODE ............................................................. 8

2.7 PARAMETER

ACCESSING AND DISPLAY ......................................................................... 9

2.7.1

HOW TO ACCESS AND DISPLAY IEMCA PARAMETERS .............................................. 10

2.7.2

ACCESSING AND DISPLAYING SUBJECT MENU PARAMETERS ................................. 12

2.8 PARAMETER

MODIFICATION

...........................................................................................

2.9

EXITING THE PARAMETERS............................................................................................. 15

2.10

PROGRAMME ARCHIVE ON SD MEMORY ...................................................................... 16

2.11 OPERATOR

PARAMETERS: DESCRIPTION .................................................................... 20

2.12

ERRORS - CAUSES - SOLUTIONS .................................................................................... 57

2.13 PROGRAM

IDENTIFICATION

DATA: DISPLAY MODE .................................................... 71

INFORMATION FOR SET UP KID 80 SIV .......................................................................... 1

3.1 PROTECTED

PARAMETERS: DISPLAY ............................................................................. 2

3.2

HOW TO ACCESS AND DISPLAY THE PROTECTED PARAMETERS .............................. 2

3.3 PROTECTED

PARAMETERS: DESCRIPTION .................................................................... 5

3.4

PARAMETERS FOR REFERENCE VALUES: DESCRIPTION ............................................ 6

3.5

AXIS FUNCTION PARAMETERS: DESCRIPTION ............................................................ 16

3.6 INTERFACE

PARAMETERS: DESCRIPTION .................................................................... 20

3.7 GENERAL

PARAMETERS: DESCRIPTION ....................................................................... 21

INFORMATION FOR THE AUTHORISED TECHNICIAN KID 80 SIV ................................ 1

4.1 PROTECTED

PARAMETERS:

ENTERING AND CHECKING ............................................. 2

4.2

MODIFYING THE PROTECTED PARAMETERS ................................................................. 2

ATTACHMENTS KID 80 SIV ............................................................................................... 1

Содержание KID 80 IV Touch



























































































































Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды

IEMCA KID 80 IV Touch, Инструкция по эксплуатации

Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды