IEMCA KID 80 IV Touch Скачать руководство пользователя страница 77

Страница: 77 / 122

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 63 / 71

5 - ERROR: SHORT FEEDING

Error: A BAR PUSHER SHORT FEEDING MOVEMENT HAS BEEN DETECTED IN ACCORDANCE
WITH THE SETTINGS OF PARAMETERS 5 and 6.

CAUSE SOLUTION

Warning
Short feeding

The tolerance values of parameters
5 and 6 are too low.

Check the tolerance values with
regards to the length of the piece to be
machined.

The lathe collet does not open
correctly.

Check the correct opening of the collet
(at least 0.5 mm).

Encoder operation failure.

Check the value relative to the position
of the bar pusher carriage on the
display and check the effective variation
of the value with regards to the real
displacement of the carriage.

The thrust received by the bar is
too low.

Check the values of parameters 7, 8
and 34.

"A" - Short piece safety

tolerance (subparameter

Par.5), Short feeding

safety (subparameter

Par.6).

"C" - Headstock stroke

(Parameter Par.5).

Feeding (Parameter

Par.6).

The bar slides out of the collet
during the headstock stroke.

Check the bar pusher collet state.

Содержание KID 80 IV Touch



























































































































Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды

IEMCA KID 80 IV Touch, Инструкция по эксплуатации

Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды