IEMCA KID 80 IV Touch Скачать руководство пользователя страница 79

Страница: 79 / 122

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 65 / 71

8 - PRESET QTY. REACHED, RESET - P26

Warning: THE BAR FEEDER HAS STOPPED AUTOMATICALLY DURING THE MACHINING PHASE.

CAUSE SOLUTION

Warning
Preset QTY. reached, reset!

The set quantity of pieces has been
reached.

Reset the number of pieces and restart.

9 - OPEN COLLET TIMEOUT

Warning: THE BAR FEEDER HAS STOPPED WITH THE ACTIVE FEEDING SIGNAL SINCE THE
OPEN COLLET "TIMEOUT" HAS ELAPSED.

CAUSE SOLUTION

Warning
Open collet timeout

In the AUTOMATIC mode the lathe
collet remained open for a longer
period than the one set in
parameter 22.

Check the value of parameter 22, with
regards to the real "FEEDING" time.

10 - BAR FEEDER EMERGENCY

Warning: THE GENERAL CONTROLS OF THE BAR FEEDER ARE NOT INSERTED.

CAUSE SOLUTION

Warning
Bar feeder emergency

An emergency button has been
pressed.

Check the state of the emergency
button.

There is an emergency signal from
the lathe.

Check whether the signal sequence
arriving from the lathe is continuous:
the signals must be all on or all off.

There is an open guard in the lathe
or in the bar feeder.

Check if the guards are closed.

Содержание KID 80 IV Touch



























































































































Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды

IEMCA KID 80 IV Touch, Инструкция по эксплуатации

Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды