IEMCA KID 80 IV Touch Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 122

background image

2 - INFORMATION FOR USE

KID 80 SIV

EN

2 - Pag. 21 / 71

This value refers to point (F) (maximum bar pusher feeding point), and is a higher length than
value (A).
The lathe enters a subprogram corresponding to a new machining cycle, where the length of the
piece to be machined is shorter than the one of the main program.

INFORMATION:

If the Bar End Adjustment subparameter 1 is used, the bar end adjustment value

should be set according to the length of the piece in the 2nd working cycle.

2) the subparameter allows opening the additional bush
Procedure for setting the "Bar End 1 Adjustment" subparameter for the additional
bush opening

a) Additional bush opening synchronized with the length of the machined piece

- Move the lathe headstock "K" in its completely forwards limit stop position;

- move the bar pusher "S" forwards without the

bar inside the guide channel positioning the
front part at about 30 mm from the additional
bush "L";

- Check the value relative to the position "F" on

the display (which by definition is called
"PdF1")

- the measured value shall be added to the

value set in the "Bar End Adjustment"
parameter and inserted in "Bar End 1
Adjustment" parameter

b) Additional bush opening at a fixed value

- Move the lathe headstock "K1" in its completely back limit stop position;

- move the bar pusher "S" forwards without the bar inside the guide channel positioning

the front part at about 30 mm from the additional bush "L";

- Check the value relative to the position "F" on the display (which by definition is called

"PdF1")

PRESS START

«
...
33
34
35
36
37
...
»

Содержание KID 80 IV Touch



























































































































Отзывы:

Нет отзывов

Похожие инструкции для KID 80 IV Touch

Бренд: Jacobs Ladder Страницы: 16

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Haigh Страницы: 60

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Gaspardo Страницы: 88

Бренд: Major tech Страницы: 12

XMLT-24ELED-200CA8-1

Бренд: DS Produkte Страницы: 28

Бренд: Asaklitt Страницы: 5

Бренд: halstrup-walcher Страницы: 47

Бренд: BSi Страницы: 2

Бренд: Kellfri Страницы: 48

Bonnet Neve KALEIDO H12 EFFICIA Design

Бренд: EPTA Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды