IEMCA KID 80 IV Touch Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 122

background image

EN

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 66 / 71

11 - WRONG FACING POSITION

In automatic mode, the facing position has been reached and the overrun position, as defined
in subparameter 3, has been exceeded.

CAUSE SOLUTION

11

Warning
Wrong facing position

When the bar does not stop in the
facing position (parameter 65), but
exceeds this point by a value higher
than or equal to the set value in the
"Overrun admitted after I"
subparameter. This check is
performed only when the "FACING
IN POSITION" mode is active and if
the set value in the "Overrun
admitted after I" subparameter is >
0.

Make sure that the chain is correctly
tensioned.

The values for "Facing and overrun
admitted after I" set by the operator are
wrong.

13 - PIECE TIMEOUT

Warning: THE WORKING CYCLE FOR MACHINING A PIECE HAS TAKEN LONGER THAN THE TIME
SET IN PARAMETER 23.

CAUSE SOLUTION

13

Warning
Piece timeout

The working cycle for machining a
piece has taken longer than the
time set in parameter 23.

Check the setting in parameter 23 with
regards to the working cycle.

The working cycle for machining a
piece has undergone an
interruption or a slowdown.

Make sure that the actual duration of
the working cycle does not face
slowdowns or interruptions.

INFORMATION:

The alarm described above also appears when the following conditions are met:

in automatic mode with the open collet signal for 1 hour; in automatic mode

with the closed collet signal and parameter 24 Synchronization to 1 for 1 hour.

«
...
78
79
80
81
82
...
»

Содержание KID 80 IV Touch



























































































































Отзывы:

Нет отзывов

Похожие инструкции для KID 80 IV Touch

Бренд: Laica Страницы: 4

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: Jacobsen Страницы: 20

Бренд: Jet Страницы: 12

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: Yamaha Страницы: 16

Бренд: Zero88 Страницы: 26

Бренд: HAMOKI Страницы: 7

Бренд: H&S Страницы: 56

Бренд: XFit Страницы: 16

BlackBox Series

Бренд: Nakamichi Страницы: 23

Бренд: Harken Страницы: 4

Бренд: A&D Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды