IEMCA KID 80 IV Touch Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 122

background image

3 - INFORMATION FOR SET UP

KID 80 SIV

EN

3 - Pag. 19 / 23

no. 79 Torque reduction in automatic mode

Defines the torque value of the bar pusher in
automatic mode. This value is expressed as a
percentage of the maximum torque.

Parameters:
A - Limitation of automatic speed

Subparameters:
B - Collet closed
C - Collet open

no. 84 Keyboard on the opposite side

Allows setting the direction of the controls for
the bar pusher movements.
The setting of this parameter should be done
with regards to the position of the keyboard
i.e.: if it is on one side or on the opposite side.
0 - Defines the movements, forwards and
backwards, in both directions.
1 - Defines the movements, forwards and
backwards, of the opposite directions with
regards to 0.

79

no. 79 Torque reduction in automatic

mode

CURRENT VALUE

Vmax

Closed collet

Vmax

Open collet

Vmax

DEFAULT VALUE

PROGRAMMABLE VALUE

Kid 80

Kid 80

A /

/

B 10

/

C

40

/

84

no. 84 Keyboard on the opposite side

DEFAULT VALUE

PROGRAMMABLE VALUE

Kid 80

Kid 80

1 0/1

«
...
103
104
105
106
107
...
»

Содержание KID 80 IV Touch



























































































































Отзывы:

Нет отзывов

Похожие инструкции для KID 80 IV Touch

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: QBC Diagnostics Страницы: 65

Бренд: BACtrack Страницы: 16

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Eaton Страницы: 21

Бренд: Eaton Страницы: 70

Бренд: NANO Страницы: 4

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

WELCH LVS 600 T

Бренд: Gardner Denver Страницы: 68

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренд: Unika Страницы: 8

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

Бренд: GGM gastro Страницы: 3

Бренд: Wartmann Страницы: 56

Бренд: KUHN Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды