IEMCA KID 80 IV Touch Скачать руководство пользователя страница 19

Страница: 19 / 122

2 - INFORMATION FOR USE

KID 80 SIV

2 - Pag. 5 / 71

2.4

BAR FEEDER STOP

Bar feeder stop in emergency.

1. Press the emergency button to stop the bar feeder.

WARNING - CAUTION

If the emergency stop is activated whilst the lathe is working, before restarting

the working cycle, check that no dangerous conditions have been created due to

the sudden stop. For example: if the tool was removing chips, move the tool

away from the work piece before restarting the lathe.

Stopping the bar feeder at the end of the machining cycle.

WARNING - CAUTION

When stopping the machine normally, do not use the emergency buttons.

1. Complete the operations of your working schedule.

2. Stop the bar feeder:

3. Stop the lathe.
4. Turn off the electrical supply of the bar feeder by turning the main switch to the 0 (OFF)

position.

Содержание KID 80 IV Touch



























































































































Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды

IEMCA KID 80 IV Touch, Инструкция по эксплуатации

Результаты поиска

Содержание KID 80 IV Touch

Отзывы:

Похожие инструкции для KID 80 IV Touch

Бренды по названию

Популярные бренды