IEMCA KID 80 IV Touch Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 122

background image

2 - INFORMATION FOR USE

KID 80 SIV

EN

2 - Pag. 3 / 71

2.2

OFFSET PROCEDURE (ADJUSTMENT)

Foreword

This procedure must be performed to optimize the bar feeder axis movements. This procedure
should be performed occasionally (once a month is recommended) to compensate any wear of
the mechanical feeding units that could alter the AXIS control operations.

INFORMATION:

Before performing the following procedure make sure that the mechanical parts

have no clearances and that the zero axis sensor is positioned correctly (it shall

not to be too retracted).

For the offset procedure perform the following operations in the given order:

1 - Set the machine to manual mode

.

2 - Carry out the bar feeder zero setting

.

3 - Bring the bar pusher carriage to the centre of the bar feeder

.

4 - Provide the enabling signal for operations keeping the zero position sensor active using a

security block or screwdriver and check that the axis moves.

5 - If the axis does not move, go straight to point 6; if it moves, adjust the value of the

machine parameter no.70, under the item "Ax. Offset Compensat." in accordance with the
"displacement" movement that the axis is carrying out; if the axis moves forward
decrease the set value and if the axis moves towards zero, increase the set value. When
the axis is still and stays in position for at least 20 seconds, the value set can be
considered correct.

6 - Carry out an absolute movement (e.g.: the first movement in step by step) and make

sure, through the operator panel (OP), that the axis is positioned with a maximum error
of +/- 0.1 mm; make sure also that the position does not undergo variations.

«
...
15
16
17
18
19
...
»

Содержание KID 80 IV Touch



























































































































Отзывы:

Нет отзывов

Похожие инструкции для KID 80 IV Touch

Бренд: Olympus Страницы: 86

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: Baker Hughes Страницы: 168

Бренд: GE Страницы: 698

Бренд: IBS Scherer Страницы: 64

Бренд: National Instruments Страницы: 10

Бренд: Wassermann Страницы: 24

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 52

Бренд: Abus Страницы: 8

Бренд: Lutron Electronics Страницы: 10

Бренд: Mikrona Страницы: 12

Бренд: Mark Fitness Страницы: 10

SonicShield I Micro

Бренд: CMS Marine Страницы: 15

Бренд: Dean Страницы: 2

Бренд: HunterLab Страницы: 29

neoBLUE LED Phototherapy Radiometer

Бренд: natus Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды