IDS X16 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 87

background image

IDS X Series Training V2.3 | Global Settings

19

Location 16: Trouble Display

Location Type: Bitmap
When the alarm system detects any of the trouble conditions are enabled in the table below, the power

light on the keypad flashes and can be set in location 14, option 2, to beep. To view the trouble condition:
Press and hold the [7] key down until the beep.
When the trouble condition has been corrected, pressing and holding [7] until the beep, and then press

the [#] key to clear the power LED trouble condition. Some troubles will clear themselves, E.g. AC Fail

LED Default

Action

Description

1

ON AC fail trouble display

This trouble condition monitors the AC that powers the
Alarm Panel and will register a trouble condition after the
time programmed in location 15. This will only clear when
AC is restored

2

OFF

Reporting comms fail trouble
display

This is if the panel tries to communicate and fails to
communicate after trying the number of times in location
47

3

OFF Phone line trouble display

A trouble condition will be displayed when telephone line
goes down.

4

ON Siren tamper trouble display

This option looks for a load and when this load goes

missing a trouble is indicated

5

ON

Low battery detection trouble
display

The alarm system tests the battery every 30 min. If a

trouble is encountered a condition will be shown

6

OFF Aux. 12V trouble display

When there is a short or some sort of trouble that causes
the 12V output to fail

7

OFF Engineer‟s reset trouble display

If this option is set in partition options (location 211 to 218)
and the alarm triggers, this option will show and the alarm

can only be armed again once the installer code has been
entered.

8

ON Box tamper trouble display

If the alarm control box is fitted with a switch that is
connected to the tamper pins on the control board and
enabled in location 14 and the door of the box is opened
a trouble will be displayed

9

OFF Peripheral tamper trouble display

If any peripheral‟s tamper have been set and any tampering will
cause this option to be displayed

10

OFF 485 bus fail trouble display

This will display when a device attached to the system via
the bus fails and stops communicating

11

OFF

Peripheral low power/ battery
display

If an expander detects low power on the 12V terminal a
trouble condition will be displayed

12

OFF Wireless battery low

When a wireless device‟s battery needs to be replaced the
device will send a battery low signal and trigger a trouble if
enabled

13

OFF Wireless supervision Monitoring

Each wireless device will check in and if a device does not a
trouble is triggered

14

OFF Wireless RF jam

If an unknown signal that can interfere with signals from
wireless is detected a trouble will be triggered

15

OFF Wireless low RSSI

RSSI is signal strength measurement and if lower than 20% a
trouble will be logged

16

OFF Zone tamper

If a zone is monitored for tamper and then a tamper signal is
detected by the alarm a trouble will be triggered.

«
...
17
18
19
20
21
...
»

Содержание X16
























































































Отзывы:

Нет отзывов

Похожие инструкции для X16

Бренд: GE Страницы: 7

Бренд: JBL Страницы: 28

Бренд: JBL Страницы: 16

Authentics L 16

Бренд: JBL Страницы: 17

Бренд: Vacron Страницы: 2

RoboSHOT 12 HD-SDI

Бренд: VADDIO Страницы: 73

Бренд: auna multimedia Страницы: 124

Бренд: Tracer Страницы: 12

Бренд: Unimig Страницы: 14

Бренд: Gladen Страницы: 2

Бренд: TCL Страницы: 20

Бренд: Wisenet Страницы: 2

Бренд: A1 Security Cameras Страницы: 2

Бренд: Q-See Страницы: 9

Бренд: Texecom Страницы: 15

Бренд: teko Страницы: 4

Бренд: Dorlen Страницы: 2

Бренд: IONIC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды