IDS X16 Скачать руководство пользователя страница 42

Страница: 42 / 87

Wireless | IDS X Series Training V2.3

Trigger the device and the display will show the signal strength on the first row.

Signal strength displayed in percentage

Sub Location 4: Supervision monitoring

Supervision is the monitoring of wireless devices to make sure that they remain communicating with the

system. In this sub location you can choose the time that the alarm waits before raising a trouble condition

if it has not received a signal from a device.

Note: When entering this sub-location the first supervision time displayed is the entered time

Upon entering location 260 and entering option 4 the following will be displayed

3 Hr Check-in

12 Hr Check-in

Flashing

Enter the supervision time required by entering the correct option from the following table.

Option

Description

3 Hours

24 Hours

Upon entering location 260 and scrolling or entering option 4 the following will be displayed:

Scroll using Medical or Panic Keys, Enter with [*] key

Enter by pressing the [*] key

Scroll using Medical or Panic Keys, Enter with [*] key

Enter the option

Option 1

Option 2

3 hours

24 hours

Default: 2 (24 hour)
Valid range: 1 – 2

Note: All devices must be set to the correct supervision time corresponding to the selection in the

supervision monitoring sub-location. Please

appendix

for hardware supervision settings

LCD

LED

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды