IDS X16 Скачать руководство пользователя страница 21

Страница: 21 / 87

IDS X Series Training V2.3 | Daylight Savings

Location 22: Keypad Sleep Delay

Location Type: Standard
If the keypad is set in location 251 to 258, depending on the keypad‟s ID, to go into sleep mode, this
location is how long after the last key press does the keypad wait to switch of all its LEDs.
Data format: mmss

Valid Range: 0001 - 5959

Default: 0500

Location 23: User, Installer, Maintenance Code Number of Digits

Location Type: Standard
By default all codes are made up of four digits. This location can change the number of digits that make

up a code to six digits.

If the number of digits is changed to six, then:

Code

Old four-digit

code

New six-digit

code

Installer Code

9999

999999

Maintenance Code

8888

888888

Master User Code 1

1234

123456

User Codes 2-128

XXXX

XXXX00

Valid Range: 4 or 6

Default: 4

Location 24: Account Code Number of Digits

Location Type: Standard
The reporting account codes can be increased to six digits from four.
Valid Range: 4 or 6

Default: 4

Daylight Savings

Daylight savings is practiced in some countries in summer where they advanced their time to increase

daylight in the evenings and back in autumn.

Location 25: Month to Start Daylight Savings

Location Type: Standard
Select the month that daylight savings begins

Value

Month

Value

Month

Value

Month

Disabled

May

September

January

June

October

February

July

November

March

August

December

April

Location 26: Day of the Week to Start Daylight Savings

Location Type: Standard
Select the day that daylight savings begins

Value

Day

Monday Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды