IDS X16 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 87

background image

Location

Sub
Loc.

Description

Explanation

304 to 307

1 to 16 Zone alarm reporting

When the system is armed, a 24Hr zone or a panic zone is triggered
this code is reported

308 to 311 1 to 16 Zone alarm restoral

When the zone restores after being violated this code is sent

312 to 315

1 to 16 Zone tamper reporting

If the tamper monitoring option is enabled and a tamper signal is
received this code is sent

316 to 319 1 to 16 Zone tamper restoral

Once the tamper condition is corrected a restoral is sent

320 to 323

1 to 16 Zone bypass reporting

If a zone is bypassed and the alarm is armed this code is sent to
report which zones are inactive

324 to 327 1 to 16 Forced Arming

If the system is programmed to automatically bypass zones that are
violated when arming, this code is sent to alert the monitoring
company of inactive zones

328 to 331 1 to 16

Swinger shutdown
reporting

If swinger shutdown has been enabled and the alarm automatically
shuts down a zone that has violated the swinger shutdown settings

332 to 335 1 to 16 Swing shutdown restore

The system can be set to try and restore a zone that has been
disabled by the swing shutdown option and if it is able to restore the
zone this code is sent

Extending Contact ID Zone Reporting

Location Type: Extended
Locations 304 to 335 can be programmed with a value that will change the contact ID reporting code for
each zone to extend what can be connected to each zone and what is reported to the control room.
Example: If a gas detector is connect to zone 8
By entering 26 into location 304 sub-location 8, whenever zone 8 triggers a contact ID code, 151 (Gas

detected), is sent to the control room.
Please see

Appendix

at the end of the manual for all values.

Value CID Description

Value CID Description

01

100 Medical Zone

3C

303 RAM Checksum bad Zone

02

101 Personal Emergency Zone

3D

304 ROM checksum bad Zone

26

151 Gas detected Zone

3E

305 System reset Zone

28

153 Loss of heat Zone

3F

306 Panel programming changed Zone

Location 336 to 340: Partition reporting codes

Location Type: Extended

There is a sub-location for each of the 8 partitions.

[INSTALLER CODE] [*] [LOCATION] [*] [SUB LOC] [*] [REPORTING CODE] [*]

Loc Sub Loc Description

Explanation

336 1 to 8 Duress reporting

A user code can be programmed to send a duress signal to alert the security
company of a life threatening situation causing the user to disarm the alarm with
this code

337 1 to 8 Keypad panic

Each keypad has a panic button which when pressed can send a code alerting the
monitoring company of a situation

338 1 to 8 Fire alarm

If a fire is detected or the fire key is pressed this code will be reported

339 1 to 8 Medical Key

A medical code is sent alerting the monitoring company to send an ambulance

340 1 to 8 Keypad lockout

If a code is entered incorrectly the keypad can be set to lock for a period of time
and sent this code to alert the monitoring company

«
...
43
44
45
46
47
...
»

Содержание X16
























































































Отзывы:

Нет отзывов

Похожие инструкции для X16

Бренд: Samsung Страницы: 36

Бренд: Varian Страницы: 176

Бренд: Xilica Audio Design Страницы: 28

Бренд: Yale Страницы: 24

Бренд: Yale Страницы: 2

Бренд: Yale Страницы: 2

BL-C111A - Network Camera - Pan

Бренд: Panasonic Страницы: 2

Бренд: EDELRID Страницы: 52

Xsential QUAD-RO

Бренд: Watermark Страницы: 8

Бренд: Datavideo Страницы: 136

Бренд: Grundig Страницы: 40

Scopia XT Advanced

Бренд: Avaya Страницы: 2

Бренд: Novus Страницы: 36

Origo Arc 4001i

Бренд: ESAB Страницы: 24

Бренд: König Страницы: 51

Бренд: i3 International Страницы: 3

Бренд: Lincoln Electric Страницы: 102

Бренд: Velleman Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды