IDS X16 Скачать руководство пользователя страница 85

Страница: 85 / 87

IDS X Series Training V2.3 | New Partition Menu on LCD keypads

Changing between Alphanumeric Mode and LED Simulation Mode

This feature allows a quick look at all zones and what state they are in.

[Mode] [4] [*] [Option] [*]

Zone Restored

This larger view shows how to distinguish between a zone that is

not

violated or restored and a zone that is violated

Zone Violated

New Partition Menu on LCD keypads

When entering quick arm, stay arm or stay go and the option is enabled all partitions will be shown with

their status

Menu status options:

r = ready

ii.

n = not ready

iii.

E = entry/exit delay

iv.

S = stay armed

A = away armed

LCD Screen

vi.

! = alarm

Note: This option must be enabled under installer settings, location 251 – 258: Keypad

Options

Press and hold
until beep

LED Mode
Menu Option

1= Alphanumeric

2 =LED simulation

Zone 1 to 16

Zone 17 to 32

Zone 33 to 48

Zone 49 to 64

Partitions

Status

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды