IDS X16 Скачать руководство пользователя страница 37

Страница: 37 / 87

IDS X Series Training V2.3 | Keypad Configuration

Location 243: Keypad ID

Enter this location physically on the keypad that you want to know the ID for.

Location 251 to 258: Keypad Options

Location Type: Bitmap
Each keypad can be set with the following options:

Option Default

Action

Description

The keypad will timeout
back to its default partition
after it has been used to
view another partition

If a keypad is made global, i.e. The keypad will be able to view
other partitions on the system. This option will automatically
return the keypad to its home partition which was programmed
into location 240

OFF

Keypad sleep mode

If this is enabled, the keypad will switch all its LEDs off after the
time programmed into location 22. Press any key to wake it up.

OFF

Global keypad status

If this is enabled the keypad can view any partition on the
system. This option ties in with option 1.

OFF

Show all Zones

If the keypad is set to global this option determines if the user
sees all zones, ON or only the zones that belong to the partition

OFF

Partition Menu

Shows all partitions if any of the following keys are pressed:
1-Quick Arm Key, 5-Stay Arm Key, 6-Stay and Go Key

OFF

Stay Menu

This option will ask for a profile number when the stay key,[5] is
pressed to arm in the stay profile

Exercise:

Configure keypad 1, to be a global keypad with the partition menu active

Instructions

Key presses

Enter the location for keypad 1

[2][5][1] [*]

Option 3 must be enabled

[3] [*]

Enable partition menu

[5] [*]

Exit the location

[#]

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды