IDS X16 Скачать руководство пользователя страница 47

Страница: 47 / 87

IDS X Series Training V2.3 | Triggering Outputs

The X-Series alarm panel has 5 physical outputs on the main board, each expander has 2 and the X64

system can have up to 6 expanders. Each of the possible 8 keypads has an output. Below shows the
number assigned to each of the available outputs.

Number

Physical Outputs

Number

Physical Outputs

Disabled

Zone expander 4 output 2

Onboard output 1

Zone expander 5 output 1

Onboard output 2

Zone expander 5 output 2

Onboard output 3

Zone expander 6 output 1

Onboard output 4

Zone expander 6 output 2

Onboard output 5

Keypad 1 output

Zone expander 1 output 1

Keypad 2 output

Zone expander 1 output 2

Keypad 3 output

Zone expander 2 output 1

Keypad 4 output

Zone expander 2 output 2

Keypad 5 output

Zone expander 3 output 1

Keypad 6 output

Zone expander 3 output 2

Keypad 7 output

Zone expander 4 output 1

Keypad 8 output

When allocating an output to an event, an action must also be entered so that the system knows what to

do when triggered.
The action can be either a pulse or latch as discussed before. Below are the values for the actions.

Value

Output Action

ACTION

Set Output High (Set)

From 0V to 12V

Set Output Low (Reset) From 12V to 0V

Pulse Output High

From 0V to 12V back to 0V

Pulse Output Low

From 12V to 0V back to 12V

When entering the value into the location follow the following steps:

Enter the output number that is to be triggered. [0][5]

Then enter the action to be performed. [0][2]

Only once the output number and the action have been entered press [*]

Outputs can be triggered by many different events and we will discuss the most common first.

Location 380: Clear Programmable Onboard Outputs on Disarm

Location Type: Bitmap
Any outputs enabled in this location will be reset when the alarm system is disarmed.
The onboard outputs are 1 to 5.
Default: OFF

Location 381 to 386: Clear Programmable Zone Expander Outputs on Disarm

Location Type: Bitmap
Any outputs enabled in this location will be reset when the alarm system is disarmed.
The zone expander outputs are:

Expander

Output

10 11 12 13 14 15 16 17

Default: OFF

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды