IDS X16 Скачать руководство пользователя страница 84

Страница: 84 / 87

Alarm Memory | IDS X Series Training V2.3

Changing Partitions

This option allows a user to access different partitions on a keypad.

[Mode] [1] [*] [Partition] [*]

Note: This will only be available if the keypad is a global keypad.

(Keypad Options Location 251 to

258)

Changing Stay Profiles

There are four stay profiles that can be created for different requirements, for example: When staying at

home in the evening the outside detectors can be activated while the indoor detectors are bypassed.

Then when going to bed all external and internal detectors except the bedrooms are made active by

changing the profile.

[Mode] [2] [*] [Stay Profile] [*]

Setting Outputs 1 to 5

Outputs, one to five, can be manually triggered on or off, via the keypad.

[Mode] [3] [*] [Output [*]

Alarm Memory

Alarm memory holds information on zones that triggered, tampered with and bypassed for the arm cycle

that has just been disarmed. Once the system arms again this information is cleared, ready for any new
information to store.
To access this information: press and hold [0] until the beep.

Key press

Information displayed

Explanation

Hold [0] until beep

Any zones that were
violated

All zones that triggered while the system was armed will
be displayed

Press [2] [*]

Zones that were bypassed Any zones that were bypassed for that arm cycle

Press [3][*]

Tampered zones

All zones that were fiddled with and their tamper
monitoring circuits triggered

Press [6] [*]

Event log

Press and hold

until beep

Menu
Option

Partition
Number

Press and

hold until

beep

Stay Profile
Menu Option

Stay Profile
Number

Press and

hold until

beep

Output

triggering Menu

Option

Output Number

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды