IDS X16 Скачать руководство пользователя страница 5

Страница: 5 / 87

IDS X Series Training V2.3 | Hardware

Hardware

1. Kick Start Jumper

When connecting to a battery, without 16VAC connected, the X-Series will

not power up until the kick start jumper has been shorted for a second. This

feature has been included so that if the battery voltage starts fluctuating and

goes below 10.5 volts, without AC, the panel switches off, stopping the

alarm from entering any undesirable states that could compromise the

integrity of the system. When AC is applied the alarm will power up

automatically.

2. Default button & 3. Panel Status LED

To default the panel, physically remove power from the unit and press down the

default button. Replace power whilst still holding down the button. Wait until the

panel status LED flashes once and then release the button.

The status LED indicates the condition of the operating system.

4. Serial Output

The serial output is for connecting the voice module, serial communicators and direct download device.

1. Kick Start

7. Connectors

5. Outputs

3. Status LED

Figure 1 X-Series Alarm Panel

6. Onboard
Expander Connector

Serial Out

K/START

2. Default Button

Serial Connector

Ground

Default Button

Panel Status LED

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды