IDS X16 Скачать руководство пользователя страница 55

Страница: 55 / 87

IDS X Series Training V2.3 | Event Reporting Codes

Location 575 Global Split Reporting

Location Type: Bitmap

LED On/Off Action

Explanation

Split
Reporting
Option

Default

OFF

IDSwift Download
Accessed

This option reports when the system has been
communicated with by the download software

OFF

Location 581 - 588 Partition Split Reporting

Location Type: Bitmap

LED On/Off Action

Explanation

Split
Reporting
Option

Default

Duress reporting

When a user code is made into a
duress code and is used this
enables the contact ID code to be
sent to the security company

OFF

Keypad Panic Reporting

When the “P” key on the keypad is
pressed a panic signal is sent to the
security company

OFF

Fire reporting

When the “F” key is pressed or a
zone is a fire zone and is violated a
fire signal is sent to the security
company

OFF

Medical Reporting

When the “M” key or the option
“Medical alarm if no movement is
detected” is enable a medical signal
will be sent if this option is enabled

OFF

Keypad Lockout Reporting

If this option is enabled in location
221 – 228 and an incorrect code is
entered the number of times set in
location 20 within the time set in
location 21, the signal will be sent

OFF

Reserved

Off

Arm without user code

Reporting

When arming with the “Quick Arm”
keys or a arm/disarm zone this
option must be enabled to send an
arm signal

OFF

Reserved

Location 600 - 616 Voice Module Reporting

Location Type: Standard

The voice module, if installed, will report programmed events to the telephone numbers entered into these

locations. Depending on the location the telephone number is entered into will depend on the partition the

person can interact with via the voice module.

Содержание X16
























































































Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды

IDS X16, Руководство по обучению

Результаты поиска

Содержание X16

Отзывы:

Похожие инструкции для X16

Бренды по названию

Популярные бренды