IBM BladeCenter HS22V 7871 страница 70 Скачать руководство пользователя | Manualshive

Страница: 70 / 258

background image

blade server, expansion unit, or blade filler. Do not operate a BladeCenter
unit for more than 1 minute without a blade server, expansion unit, or
blade filler in each blade bay.

3.

Make sure that the release handles on the blade server are in the open
position (perpendicular to the blade server).

4.

Slide the blade server into the blade bay until it stops.

5.

Push the release handles on the front of the blade server to the closed
position.

Note:

After the blade server is installed, the service processor in the blade

server initializes and synchronizes with the management module. This process
takes approximately two minutes to complete. The power-on LED flashes
rapidly, and the power-control button on the blade server does not respond
until this process is complete.

6.

Turn on the blade server (see “Turning on the blade server” on page 13 for
instructions).

7.

Make sure that the power-on LED on the blade server control panel is lit
continuously, indicating that the blade server is receiving power and is turned
on.

8.

If you have other blade servers to install, do so now.

9.

Optional: Write identifying information on one of the labels that come with
the blade servers and place the label on the BladeCenter unit bezel. See the
documentation for your BladeCenter unit for information about the label
placement.

Important:

Do not place the label on the blade server or in any way block the

ventilation holes on the blade server.

10.

Reinstall the bezel assembly on the BladeCenter T unit (BladeCenter T unit
only). For detailed instructions for reinstalling the bezel assembly, see the

Installation and User's Guide

that comes with the BladeCenter T unit.

If you have changed the configuration of the blade server or if you are installing a
different blade server from the one that you removed, you must configure the
blade server through the Setup utility, and you might have to install the blade
server operating system. Detailed information about these tasks is available in the

Installation and User's Guide

.

54

BladeCenter HS22V Type 7871 and 1949: Problem Determination and Service Guide

«
...
68
69
70
71
72
...
»

Содержание BladeCenter HS22V 7871



































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeCenter HS22V 7871

BladeCenter HS22

Бренд: IBM Страницы: 18

Бренд: Z Microsystems Страницы: 17

Бренд: TYAN Страницы: 106

Netfinity 1000-8477 21Y

Бренд: IBM Страницы: 268

Mobileraid MR8X

Бренд: Sans Digital Страницы: 81

Бренд: LiveU Страницы: 14

Бренд: TYAN Страницы: 70

ZPS3611 - QUICK

Бренд: Zonet Страницы: 1

Бренд: ZLAN Страницы: 13

Ultra Enterprise 3000

Бренд: Sun Microsystems Страницы: 48

Бренд: Axis Страницы: 85

Бренд: Xerox Страницы: 2

Бренд: Advantech Страницы: 140

Бренд: ZyXEL Communications Страницы: 115

LAN Brick Eth 10

Бренд: MPI Technologies Страницы: 2

Бренд: Infoblox Страницы: 28

Бренд: Amulet Hotkey Страницы: 2

Бренд: EVS Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды