IBM BladeCenter HS22V 7871 страница 32 Скачать руководство пользователя

Страница: 32 / 258

Switch number

Description

Switch setting

Definition

SW1 - 5

Boot block recovery

The default position is
off, allowing the blade
server to boot from the
primary UEFI
firmware.

When the switch is on
it allows the blade
server to boot using
the backup UEFI.

SW1 - 6

IMM force update

The default position is
off.

For trained service
technician only.

SW1 - 7

Wake on LAN (WOL)
disable

The default position is
off.

Turning this switch to
the on position
disables WOL.

SW1 - 8

Force H8 update

The default position is
off.

N/A

SW3

Light path diagnostics
switch

The default position is
off. Turning this switch
on lights the light path
diagnostic LEDs.

Push down on the
light path diagnostics
switch push button to
light the diagnostic
LEDs.

BladeCenter HS22V Type 7871 and 1949: Problem Determination and Service Guide

Содержание BladeCenter HS22V 7871



































































































































































































































































Результаты поиска

Содержание BladeCenter HS22V 7871

Отзывы:

Похожие инструкции для BladeCenter HS22V 7871

Бренды по названию

Популярные бренды

IBM BladeCenter HS22V 7871, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание BladeCenter HS22V 7871

Отзывы:

Похожие инструкции для BladeCenter HS22V 7871

Бренды по названию

Популярные бренды