HySecurity StrongArmPark DC Скачать руководство пользователя

Страница: 92 / 96

Str

ongArmPark DC: Lighting Connection

Make sur

e both AC and DC power switches ar

e turned OFF

Insert leads of wir

e harness thr

ough the hole in chassis between

the two bracket mounts. Feed the cable thr

ough the interior of

the chassis. Pull enough cable to r

each the Smart DC Contr

oller

terminals.

NOTE:

Connect wir

e lead (female quick connect) l24V to 24VDC.

Lights will be dim if lead is connected to 12VDC terminal.

Attach the end of the wir

e harness (on the outside of the

chassis) to the LED light connector on the arm. The wir

e harness

connector is keyed. Be sur

e to seat the connectors befor

thr

eading close. See illustration on pr

evious page.

Make sur

e the harness is secur

ed to the chassis with the strain

relief bushing. See illustration on pr

evious page.

+24V

DC Power

Switch

AC Power

Switch

LED Arm light connector

Wir

e harness

connector

Connect Arm Light Cables

Turn OFF AC and DC power

Shown separated

for r

efer

ence only

ire ties

Factory installed magnet

(kill switch)

End cap

Knob

eakaway

fasteners

Connections to Contr

oller

Female Quick Connects:

User2 Relay (NO) & +24VDC

Spade connections:

COM & SENSOR 3

Spline collar

bolt & nut

Exploded V

iew

Smart DC Contr

oller: Menu Mode Navigation Buttons

To access

Menu mode

To change menu item

appearing in the display

To navigate thr

ough

the menu item selections

ess the Menu button

twice.

ess Select.

Two left characters blink.

ess Next or Pr

evious.

Continue pr

essing Next to view all

selections.

To choose what item appears

on the display

To navigate between

menu items

ess Select.

Blinking characters

become static.

ess Next or Pr

evious.

Advance - pr

ess Next

evious - pr

ess Pr

evious

Connect female quick connect l24V to the

24VDC

power supply terminal. See wiring illustrations.

Connect the second female quick connect to the NO terminal on

User Relay 2.

NOTE:

If you ar

e planning to pr

ogram the pr

oximity sensor in the br

eakaway

bracket assembly

, connect one spade connection to COM and the other to

SENSOR 3 (Photo Eye Close on BY1 operators).

Spade

connections

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

www.hysecurity.com

Содержание StrongArmPark DC

































































































Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды