HySecurity StrongArmPark DC Скачать руководство пользователя страница 40

Страница: 40 / 96

ettIng

tHe

Ime

and

ate

A feature of the Smart DC Controller is its 24-hour, 365 day clock. Make sure

it is set to the appropriate time zone. An accurate time and date allows the
diagnostic log to date stamp operational data which indicates when Alerts,

Faults and Errors occur. The log helps in troubleshooting and can be viewed
using the S.T.A.R.T. software application via a laptop connected to the USB or

RS-232 port. For more information, refer to

Smart Touch Analyze and Retrieve

Tool (S.T.A.R.T.) on page 71

To set or adjust the time or date, take the following steps:

At a gate status display, press the MENU button twice. This accesses

the User Menu and the CLOSE TIMER display appears.

Press NEXT or PREV until the SET CLOCK display appears.

Press SELECT.

4. CL blinks.
5.

Press NEXT or PREV to change the number to 1.

Press SELECT to accept the display.

The date and time display appears. Use the SELECT and NEXT

buttons in the same manner as before to adjust the date and time.

NOTE:

A date or time field must be blinking before it

can be changed.

To accept what appears on the date and time display, press SELECT.

To exit the User Menu, press the MENU button. A gate status appears

in the display indicating you have returned to Run Mode.

NOTE:

A lithium coin battery supports the clock so the date and time is retained even when

the main power is turned off. Replace the battery about every five years with a DL 2025, DL
2032 or CR 2025 or CR 2032 battery. Refer to Clock Battery Replacement.

esettIng

pen

and

lose

ImIts

Resetting the open and close limits is easily accomplished by accessing the
Installer Menu.

CL 1

SET CLOCK

OPEN

STOP

RESET

SELECT

01/05/13 00:00

OPEN

STOP

RESET

SELECT

CT 0 (OFF)

CLOSE TIMER

OPEN

STOP

RESET

SELECT

HYSECURITY

GATE CLOSED

OPEN

STOP

RESET

SELECT

Status Display

GATE CLOSED

User Menu

CT 0 (OFF)

Installer Menu

LL 0 (OFF)

Learn Limits

LL 1 (ON)

LEARN OPEN

DEGS: +XXX.X

Press MENU twice at

the Run Mode static display.

To access the Installer Menu,

press and hold RESET &
OPEN, and then release them.

Press Select.

The “LL” characters blink.

Press Next.

Press Select. The Learn OPEN blinks in the display

indicating that the operator is ready to relearn the
closed limit.

Learn Open Limits

Press and hold the OPEN button while the degrees increase

toward 90 and the barrier arm reaches the desired full open
position.

Release the OPEN button as the arm nears full open. The motor

slows as do the numbered increments on the display. Note that if

you go too far, you can press CLOSE to reverse direction.

Press STOP twice to preserve the open stop location. The buzzer

chirps twice and the full open stop is retained in memory.

Learn Close Limits

Press and hold the CLOSE button while the degrees increase

toward - 90 and the barrier arm reaches the desired full open
position.

Release the CLOSE button as the arm nears full open. The motor

slows as do the numbered increments on the display. Note that if

you go too far, you can press OPEN to reverse direction.

Press STOP twice to preserve the open stop location. The buzzer chirps twice and the full open stop is

retained in memory.

est

tHe

perator

Complete the installation by testing the operation of the gate.

NOTE:

The operator must be turned on and in Run mode. A Run mode display appears on the SDC. If a Run mode status does not

appear on the display, press Reset. If an error, alert, or fault appears on the display, refer to the

Troubleshooting

section to learn

how to clear the display and return to Run mode.

1. Press Open to open the barrier arm.
2. Test the operator.

• Cycle the barrier arm a few times by pressing the Close and Open buttons.

NOTE:

If additional accessories are to be added, read about

SDC Inputs & Wiring on page 33

LEARN OPEN

DEGS: +XXX.X

OPEN

STOP

RESET

SELECT

LEARN CLOSE

DEGS: - XXX.X

OPEN

STOP

RESET

SELECT

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

www.hysecurity.com

Содержание StrongArmPark DC

































































































Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Бренды по названию

Популярные бренды

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Бренды по названию

Популярные бренды