HySecurity StrongArmPark DC Скачать руководство пользователя

Страница: 31 / 96

ode

The Run Mode displays appear static when the operator is ready and waiting for a run command. When the

display is flashing “GATE OPENING” or “GATE CLOSING”, a command has been received and the barrier

gate is in motion. The command may come from a variety of sources: a card reader, push-button remote,

or recognition of a vehicle passing over a loop detector. In all cases, the operator “runs” the motor when it

receives an operational command.

Three displays indicate the position or status of the barrier gate. The keypad entry used to access the User or
Installer menus, begins at one of these Run Mode displays.

Run Mode Displays

NOTE:

To access the User or Installer menus, the motor cannot be engaged and the barrier gate cannot be moving.

IeWIng

perator

tatus

IsplaYs

Press the MENU button once and the operator status displays scroll past in two second intervals. Pertinent

information appears to provide a quick overview of the operator’s status or configurations.

The type of information that may scroll across the display includes: software version, operator type (OT), gate

handing (LEFT HAND or RIGHT HAND), buss voltage, and life cycle counter.

Example of Operator Status Displays

HYSECURITY

GATE STOPPED

OPEN

STOP

RESET

SELECT

HYSECURITY

GATE OPEN

OPEN

STOP

RESET

SELECT

HYSECURITY

GATE CLOSED

OPEN

STOP

RESET

SELECT

Pressing Reset clears alerts or faults and

returns to Run Mode.

NOTE:

Press Reset at any Run mode

status display to view the software version.

For example: h5.33

Pressing Open,

Close, or Stop

causes the gate

to perform the

command.

Pressing

Menu

scrolls through operator status

displays and accesses the User Menu.

Note:

Pressing the MENU button twice, bypasses

the operator status displays.

HYSECURITY

V5.32

OPEN

STOP

RESET

SELECT

LEFT HAND

OPEN

STOP

RESET

SELECT

BULK

CHARGER STATE

OPEN

STOP

RESET

SELECT

www.hysecurity.com

Display & Menu Options

MX3650-01 Rev. D

Содержание StrongArmPark DC

































































































Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды