HySecurity StrongArmPark DC Скачать руководство пользователя | Manualshive

Страница: 36 / 96

background image

Table 4: Installer Menu

Installer Menu

Setting Options

Menu Tasks & Explanations

SDC Wire

Connections

SG 0 (OFF)
Sequenced Gate

0 = off

1 = Loop Layout/Site #1
2 = Loop Layout/Site #2

Establishes communication after wiring two or

more operators as sequenced gates.

This menu item only appears if the Dual Gate
menu item DG is set at 0 (solo operator).

NOTE:

Access the User Menu in both

operators and set a Close Timer.

Connect Dual Gate
COM (Traffic Gate)

to

Dual Gate COM
(Security Gate)
A to A

B to B

CH 0 (AC)

Charger Type

0 = AC powered charger

1 = Solar powered charger

Assigns charger type.

If a solar-powered unit is ordered and delivered
factory-ready, this menu will not appear.

NOTE:

Menu item does not appear on an AC-

powered operator.

BT 0 (STANDARD)

Battery Type

0 = standard 8Ah

1 = extended (50 Ah)
2 = maximum (110 Ah)

Assign the battery type used by the operator.

Smaller batteries are charged with less current
to avoid overheating and larger batteries are
charged with more current to supply a more
rapid charge.

Extended and

maximum batteries
require separate
housing and wiring.

FO 0 (OFF)
Fire Dept Open

0 = disabled

1 = enabled

Provides the Fire Dept. Open input and allows
a button to activate the emergency open when

connected to +24VDC. When set to 1, the

open signal received by the operator overrides
all photoelectric eyes and edge sensors, and
opens the barrier arm. Pressing the Reset or
Open button is required before the barrier arm
can be closed.

+24V

Fire Dept Open

SE 0
IES Sensitivity

0 = Maximum (highest) sensitivity

1 = Moderate sensitivity
2 = Least sensitivity

Adjusts the sensitivity of the dynamic reversing
sensor. Available settings are 0 to 2. Zero is the

default and reacts quickly (high sensitivity) to
impediments.

NOTE:

For StrongArmPark DC, adjust the

spring to prevent false trips prior to changing
the sensitivity.

See NOTE.

LC 0 (0.0 SECS)

Leaf Delay Close

0 = none

1 through 20

For example:
1 = ½ second
4 = 2 seconds
20 = 10 seconds

Delays gate closure. This menu option appears
if the gate operator is designated as a dual
gate system (Master/Second, for example).

Available settings are 1 to 20. Each increment

adds

½ second, to a maximum of 10 seconds

time delay, before the operator activates

when commanded to close.

DUAL GATE inputs

on both operators

LO 0 (0.0 SECS)

Leaf Delay Open

0 = none

1 through 20

For example:
1 = ½ second
4 = 2 seconds
20 = 10 seconds

Delays gate opening. This menu option
appears if the gate operator is designated
as a dual gate system (Master/Second, for

example). Available settings are 1 to 20. Each

increment adds

½ second (with a maximum of

10 seconds) time delay following a command

to open before the operator activates.

DUAL GATE inputs

on both operators

EC 0 STOP ONLY



Eye Close Logic

0 = Close eye stops only

1 = Reverse to full open with barrier
gates (2 second reverse to open on
swing, slide, or vertical gates)

The default setting is non-reversal if the close

photo eye is triggered. A setting of 1 causes

the barrier arm to reverse and travel full open if
triggered while closing.

EYE Close
EYE COM

(Inputs #14 or #15)

26

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

© 2017

www.hysecurity.com

«
...
34
35
36
37
38
...
»

Содержание StrongArmPark DC

































































































Отзывы:

Нет отзывов

Похожие инструкции для StrongArmPark DC

Бренд: Wayne-Dalton Страницы: 26

Бренд: BFT Страницы: 32

LiftMaster Professional 78LM

Бренд: Chamberlain Страницы: 2

Бренд: SCS Sentinel Страницы: 88

Бренд: tau Страницы: 40

Бренд: Sentex Страницы: 31

Бренд: DACE Страницы: 22

Бренд: Beninca Страницы: 18

Бренд: tau Страницы: 16

Бренд: Chamberlain Страницы: 2

Бренд: Quirky Страницы: 2

Бренд: Miller Edge Страницы: 3

Бренд: SOMFY Страницы: 2

LiftMaster Professional BG770

Бренд: Chamberlain Страницы: 2

Бренд: Schartec Страницы: 42

Бренд: Richmond Страницы: 9

Бренд: Richmond Страницы: 20

Бренд: Richmond Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды