manualshive.com logo in svg

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Поделиться
Скачать
HySecurity StrongArmPark DC Скачать руководство пользователя страница 87

CAUTION

 

Wires are attached 
to the physical stop 
bracket. Do NOT sever 
the wires or hang the 
bracket by the wires.

12

3

Using a ½-inch socket wrench, remove four 
fasteners securing the physical stop bracket. 
(Do NOT break the wire connections.) Hang the 
bracket from the side of the chassis, as shown. 

12

4

Remove the drive belt. Use a 

>\zn

-inch socket 

wrench to loosen (do NOT remove) the 4 bolts 
securing the motor to the motor plate. 

12

2

If the drive belt cover is in place, use a phillips 
head screwdriver to remove two screws that 
secure it to the motor plate. Set the drive belt 
cover and fasteners aside. 

CAUTION

 

12

5

Wires are attached 
to the motor!

•  Disconnect the 2 motor 

wire leads from the 
wire harness inside the 
chassis. 

•  Disconnect the blue 

connector wire from the 
Smart DC Controller 
and pull it out of the 
control box.

12

1

Remove the front access panel. (Keys come with 
the operator.) 
Use a phillips head screwdriver to remove the 
plastic cover from the control box.

12

6

Top cover

Drive belt cover

Drive belt

Loosen, DO NOT remove, 4 bolts 

on motor cover plate

Physical stop bracket

Two phillips head screws

Control box: 

Smart DC 

Controller 

access

Set screws

Nylon bolts for 

breakaway bracket

Motor.  

See 

CAUTION

ContInued

....

Turn the page for more information.

Disconnect the 

2 motor wires.

Disconnect wire 

leads before 

removing the motor

Remove 4 bolts and lift the motor plate 
assembly from the chassis. Set it aside.

Physical stop bracket

Reference

H

andIng

 C

Hange

All StrongArmPark DC operators are shipped from the factory in a left handing configuration unless specified 

otherwise.  If you need to change the StrongArmPark DC14 handing at the site, you will need to:  

•  Release spring tension
•  Swap locations of the spring’s eyebolt  

and spacer on the physical stop lever

•  Retention the spring

NOTE: 

If changing the handing on StrongArmPark DC10,  

follow steps 1 and 10.

www.hysecurity.com

  © 2017 

Reference 

MX3650-01 Rev. D 

  77  

Содержание StrongArmPark DC

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды