manualshive.com logo in svg

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

"HySecurity StrongArmPark DC" - автоматический шлагбаум высочайшего качества, предназначенный для контроля доступа на парковках. Для обучения и эффективной эксплуатации рекомендуется скачать бесплатное "Programming And Operations Manual" с нашего сайта. manualshive.com - место, где вы можете скачать этот руководство.

Поделиться
Скачать
background image

P

Hoto

 e

ye

 I

nStAllAtIon

 ..........................................................................................53

Photo Eyes (Non-Contact) Installation ...........................................................................................................................54

Compatibility ..............................................................................................................................................................54
Installation ...................................................................................................................................................................54
Configuration ..............................................................................................................................................................55
Photo Eye Connections: Smart Touch & Smart DC Controllers ..................................................................................55
Photo Eye Function .....................................................................................................................................................55

Retro-Reflective Photo Eye Systems ..............................................................................................................................56
Photo Eye Alignment Feature  .......................................................................................................................................57

Smart DC Controller: Menu Mode Navigation Buttons ..............................................................................................57

t

rouBleSHootIng

 ...................................................................................................59

System Diagnostic Messages .........................................................................................................................................59

Table 8: Troubleshooting Codes .................................................................................................................................60

Adjusting the Dynamic Reversing Sensor ......................................................................................................................66
Conditions Affecting the Dynamic Reversing Sensor .....................................................................................................67
Access the Event Log through the User Menu  ..............................................................................................................67
StrongArmPark DC Wiring Schematics ..........................................................................................................................68

StrongArmPark DC 10 and StrongArmPark DC 14 Schematics ..................................................................................68

StrongArmPark DC Wiring Schematics - Solar ...............................................................................................................69

StrongArmPark DCS 10 Solar and StrongArmPark DCS 14 Solar Schematics ............................................................69

g

enerAl

 m

AIntenAnCe

 ...........................................................................................71

Smart Touch Analyze and Retrieve Tool (S.T.A.R.T.)  ......................................................................................................71

What You Need  ..........................................................................................................................................................71
Installing S.T.A.R.T. Software .......................................................................................................................................71

Software Maintenance ....................................................................................................................................................72
Electrical Controls ..........................................................................................................................................................72

Clock Battery Replacement .........................................................................................................................................72
Fuse Replacement ......................................................................................................................................................72

Mechanical Maintenance ...............................................................................................................................................73

HyProtect

™

 Breakaway Arm Mount ...........................................................................................................................73

Breakaway Fasteners ...................................................................................................................................................73

Drive Belt Tension and Alignment ..................................................................................................................................74
DC Battery Replacement ................................................................................................................................................75

r

eferenCe

 .............................................................................................................77

Handing Change ............................................................................................................................................................77
Spring & Physical Stop Lever Assembly .........................................................................................................................78

Set Handing ................................................................................................................................................................78

Installation Instructions 

MX4010 ..........................................................................................................................................................................79

StrongArmPark DC Articulating Arm ..........................................................................................................................79
Assemble the Pivot Block and Connect Light Strings .................................................................................................80
Feeding the cable (LED lighting) through the Pivot Block ..........................................................................................80

www.hysecurity.com

  © 2017 

Tabnle Contents 

MX3650-01 Rev. D 

  ix  

Содержание StrongArmPark DC

































































































Отзывы:

Нет отзывов

Похожие инструкции для StrongArmPark DC

D.A.C.E DURASWING Installation And Owner'S Manual preview
DURASWING
Бренд: D.A.C.E Страницы: 16
Nice TOO3000 User & Installation Manual preview
TOO3000
Бренд: Nice Страницы: 16
Nice RS 500 AC Installer'S Instructions preview
RS 500 AC
Бренд: Nice Страницы: 28
Seav RES 2175 Wiring Instructions preview
RES 2175
Бренд: Seav Страницы: 3
tau Stargate Assembly Instructions Manual preview
Stargate
Бренд: tau Страницы: 13
Automatic Technology Axess Pro Series 1101 Installation Instructions Manual preview
Axess Pro Series 1101
Бренд: Automatic Technology Страницы: 40
FAAC S2500I CERNIERA Manual preview
S2500I CERNIERA
Бренд: FAAC Страницы: 12
Richards-Wilcox Protege FP-EU Series Installation Instructions Manual preview
Protege FP-EU Series
Бренд: Richards-Wilcox Страницы: 38
FAAC B680 Manual preview
B680
Бренд: FAAC Страницы: 42
CAME STYLO Series Installation Manual preview
STYLO Series
Бренд: CAME Страницы: 20
SWS SeceuroGlide LT Installation Instructions Manual preview
SeceuroGlide LT
Бренд: SWS Страницы: 11
Chamberlain Security+ 6200-2K Owner'S Manual preview
Security+ 6200-2K
Бренд: Chamberlain Страницы: 40
FAAC 422 Standard Translation Of The Original Instructions preview
422 Standard
Бренд: FAAC Страницы: 28
Novoferm tormatic Novomatic 200 Installation, Operating And Maintenance Instructions preview
Novomatic 200
Бренд: Novoferm tormatic Страницы: 32
Motorline professional WING400 Quick Start Manual preview
WING400
Бренд: Motorline professional Страницы: 8
Motorline professional TELICA User'S And Installer'S Manual preview
TELICA
Бренд: Motorline professional Страницы: 13
Motorline professional SIGMA X User& Installer'S Manual preview
SIGMA X
Бренд: Motorline professional Страницы: 21
Motorline professional LINCE 400 User’S And Intaller’S Manual preview
LINCE 400
Бренд: Motorline professional Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды