manualshive.com logo in svg

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Поделиться
Скачать
HySecurity StrongArmPark DC Скачать руководство пользователя страница 52

Table 7: Programmable User Relays, Revenue Control Parking Applications

Relay No.

Name

Description

Wire Connection

31

Device Reset Pulse Output

N.O. Input. A 250ms pulse occurs when the Center 
Loop is triggered. If a back out occurs, this relay 
sends a reset pulse to the access control device or 
computer system to invalidate the ticket.

R1, R3 through R10

32

Back Out Pulse Output

N.O. Input. The relay outputs a 250ms pulse when a 
back out has occurred based on the criteria given in 
the “Revenue Control Parking Functions.”

R1, R3 through R10

33

Inbound Transient/Lot Output

N.O. Input. The relay outputs a 250ms pulse used to 
increment the transient and total vehicle counts.

R1, R3 through R10

TRANSIENT USER

34

Outbound Transient/Lot Output

N.O. Input. The relay outputs a 250ms pulse used to 
decrement the transient and total vehicle counts. 

R1, R3 through R10

TRANSIENT USER

35

Inbound Tenant Output

N.O. Input. The relay outputs a 250ms pulse and 
increments the tenant counter when the Tenant User 
input is activated and OALD, then CLD, are tripped 
and released. This activity signals a prepaid customer 
has entered  the facility. 

R1, R3 through R10

TENANT USER

36

Outbound Tenant Output

N.O. Input. The relay outputs a 250ms pulse and 
decrements the tenant counter when the Tenant  
User input is activated and IALD, then CLD, are 
tripped and released. This activity signals a prepaid 
customer has exited the facility. 

R1, R3 through R10

TENANT USER

37

Inbound Special Output

N.O. Input. The relay outputs a 250ms pulse and 
increments the special counter when the SPECIAL 
USER input is activated and OALD, then CLD, are 
tripped and released. This activity signals a customer 
has entered the facility. 

R1, R3 through R10

SPECIAL USER

38

Outbound Special Output

N.O. Input. The relay outputs a 250ms pulse and 
decrements the tenant counter when the SPECIAL 
USER input is activated and IALD, then CLD, are 
tripped and released. This activity signals a customer 
has exited the facility. 

R1, R3 through 
R10SPECIAL USER

39

Set aside for Factory Use

HySecurity Testing Only

Do not use

e

xtended

 r

elaY

 m

odule

 o

ptIon

 

The extended relay module provides 8 numbered mechanical relays. R3, 
RELAY 3 LOGIC through R10, RELAY 10 LOGIC can be accessed through 

the Installer Menu. Set the number for the relay based on the information 
found in Tables 4 or 5. Table 5 is oriented toward revenue control parking 
lot applications.

Wire communication cable connections between the DUAL GATE ports, 
at the base of the SDC, and the extended-mechanical relay module. See 

illustration

Overview of the Smart DC Controller on page 34

.

 

42

 

  MX3650-01 Rev. D 

StrongArmPark DC Programming & Operations 

© 2017  

www.hysecurity.com

Содержание StrongArmPark DC

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды