HySecurity StrongArmPark DC Скачать руководство пользователя

Страница: 30 / 96

enu

ode

In Menu Mode, the motor disengages and operator commands are ignored. Data entry, menu navigation, and

menu selection can be accomplished using the buttons on the Smart DC Controller keypad.

NOTE:

Menu Mode automatically returns to Run Mode if no activity (i.e. key presses) occurs for two minutes.

The 32-character LCD display limits what can be communicated with words. If you do not understand the

abbreviated word or acronym, please review the

User Menu

and

Installer Menu

sections.

enu

ode

avIgatIon

Navigating within the program menus is easy once you learn how the keypad buttons function. Refer to the
following chart.

Smart DC Controller: Menu Mode Navigation Buttons

To change that data

appearing in the display

To navigate through the

Selections

To choose what appears on

the display

To navigate between menu

items

Press

Select

Two left characters blink.

Press

Next

Previous

Continue pressing Next to view

all selections.

Press

Select

Blinking characters

become static.

Press

Next

Previous

Advance - press Next

Previous - press Previous

CT 0 (OFF)

CLOSE TIMER

OPEN

STOP

RESET

SELECT

Pressing

Select

causes the left most two characters to blink, (CT in

the example), which indicates the display is ready

to accept changes to a menu setting.

Use the navigational buttons to view selections.

Press

Select

a second time to accept what

appears on the display. Entry mode is exited, the two characters

stop blinking, and Next or Previous must be pressed to move onto a

different display. Pressing Program exits to Run mode.

The

Menu

button accesses

program mode. When the

menu item is selected and

blinking, the Menu button

has no function. However,

pressing Menu when the

2 characters are static

(not blinking), returns the

operator to Run Mode.

32-character display provides codes

which provide information about the

menu items.

The

Reset

button is disabled

while in Program Mode.

Two blinking characters

indicate that the display

will accept changes.

NEXT or PREV

Navigational buttons.

Pressing Next or Previous

scrolls through the selections.

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

www.hysecurity.com

Содержание StrongArmPark DC

































































































Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды