HySecurity StrongArmPark DC страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 96

background image

u

ser

m

enu

The User Menu consists of several items which can be modified using the Smart DC Controller keypad.

Access:

Pressing the MENU button, at one of the static Run Mode displays, causes the operator status displays to scroll
past, stop and display the first user menu item.

When the Close Timer (or Hold to Close “HC”) display appears, it means you have accessed the User Menu.
The Close Timer display is the first in a cyclical series of User Menu displays.

NOTE:

To access the User Menu, the operator must be in Run Mode. To bypass the operator status displays, press the Menu button a

second time.

Use the navigational buttons, Select, Next, and Previous to change or view

the menu functions. Table 1 describes the User Menu items and supplies the
factory defaults. (Factory default settings shown in bold.)

Table 3: User Menu

Table 3: User Menu

User Menu

Setting Options

Menu Tasks & Explanations

SDC Wire Connections

CT 0 (OFF)

Close Timer

0 = Timer disabled (OFF)

1 second to 99 seconds

The Close Timer assigns how many seconds
before the open gate initiates closure.
Keep the setting at 0 if a hard-wired, push-button
control device is being used. Refer HC.

NOTE:

When the Hold to Close is set to 1, the

Close Timer display does not appear and HC1
becomes the User Menu entry display.

Not applicable (N/A)

HC 0 (OFF)

Hold to Close

0 = off

1 = on

Set to 0 to produce an gate closure when a
momentary signal is transmitted.
Set to 1 if a constant hold to close signal, such as

a push button control, is being used. A setting of

1 also deactivates the automatic close timer and
causes its menu to disappear. The Hold to Close
replaces the Close Timer display as the User Menu
entry display.

COM
Close

HO 0 (OFF)



Hold to Open

0 = off

1 = on

Similar to Hold to Close, but configures the Open

inputs for a constant-hold function.
Set to 1, a constant hold to open signal, such as a
push button control, must be in use.

COM
Open

AP 0 AC LOSS
UPS FAIL OPEN

0 = UPS FAIL OPEN

1 = UPS FAIL CLOSE
2 = AUTO OPEN
3 = NO CLOSE TIMER

The setting configures how the gate functions
when AC power fails.

COM

RO 0 (OFF)



Radio Open/Close

0 = off

1 = on

A setting of zero, configures radio input for open

only. Setting 1 adds the capability for radio input
to close the gate, but only when it is fully open.

COM

RADIO Open

CT 0 (OFF)

CLOSE TIMER

OPEN

CLOSE

STOP

MENU

RESET

PREV

NEXT

SELECT

22

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

© 2017

www.hysecurity.com

«
...
30
31
32
33
34
...
»

Содержание StrongArmPark DC

































































































Отзывы:

Нет отзывов

Похожие инструкции для StrongArmPark DC

Бренд: GiBiDi Страницы: 7

Бренд: Whisper Drive Страницы: 44

Бренд: ProfiTech Страницы: 8

Бренд: Winco Страницы: 8

LiftMaster 84501

Бренд: MyQ Страницы: 40

Бренд: SOMFY Страницы: 72

Бренд: SOMFY Страницы: 72

Бренд: SOMFY Страницы: 72

Бренд: Nice Страницы: 44

AMICO Series A1824

Бренд: CAME Страницы: 12

SECURITY+ 2280 1/2 HP

Бренд: Chamberlain Страницы: 36

Бренд: V2 Страницы: 48

Бренд: Rival Страницы: 4

Бренд: FAAC Страницы: 32

Smart Roller Nano

Бренд: Smart Openers Страницы: 16

Бренд: V2 Страницы: 52

Titano QK-T4000

Бренд: quiko Страницы: 9

Comfortpull 21141

Бренд: Trebs Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды