HySecurity StrongArmPark DC Скачать руководство пользователя

Страница: 42 / 96

ettIng

tHe

lose

Imer

As an added security measure and to make sure the barrier

arm closes automatically within a reasonable time frame after
all loops are cleared, you must set the Close Timer.

The Close Timer assigns how many seconds will pass before the operator initiates closure of a fully opened

barrier arm after all open commands and reversing sensor inputs have ceased and loops cleared. Every gate

operator needs to have the close timer set to a specific number of seconds (for example, 5 seconds) unless a
hard-wired closing device is connected to the unit, such as a “hold to close” push button station.

To adjust the time (1 to 99 seconds) it takes before the operator initiates gate closure, take the following steps:

At a gate status display, press the MENU button twice. This accesses the User Menu and the Close

Timer display appears.

NOTE:

If you want gate personnel to operate the gate with the Hold to Close feature found in some push

button stations, then set the Hold to Close menu item to 1. When the Hold to Close menu item is active

(set to 1), the Close Timer menu item is unavailable.

2. Use the Select, and then Next or Previous buttons to change the number of seconds appearing on the

display.

To exit the User Menu, press the MENU button. The gate status appears in the display indicating you

have returned to Run Mode.

CT 15 (SECS)

CLOSE TIMER

OPEN

STOP

RESET

SELECT

Status Display

GATE CLOSED

User Menu

CT 0 (OFF)

CT 1 (ON)

CLOSE TIMER

CT 10 (SECS)

CLOSE TIMER

MX3650-01 Rev. D

StrongArmPark DC Programming & Operations

www.hysecurity.com

Содержание StrongArmPark DC

































































































Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды

HySecurity StrongArmPark DC, Руководство по программированию и эксплуатации

Результаты поиска

Содержание StrongArmPark DC

Отзывы:

Похожие инструкции для StrongArmPark DC

Бренды по названию

Популярные бренды