Huawei NetCol8000-A013 Скачать руководство пользователя страница 98

Страница: 98 / 181

Alarm

Alarm Name

System

Action

Possible Causes

Solution

214

Comp Drive DC

Overvolt Alarm

The

compressor

shuts down.

The input voltage of

the compressor drive

board is higher than

the preset threshold.

1. Check whether the

input power is

within the normal

range.

2. Use an oscilloscope

to check whether

the waveform of the

power grid is within

the normal range.

3. Replace the

compressor drive

board if it is faulty.

215

Comp Drive DC

Undervolt Alarm

The

compressor

shuts down.

The input voltage of

the compressor drive

board is lower than the

preset threshold.

1. Check whether the

input power is

within the normal

range.

2. Use an oscilloscope

to check whether

the waveform of the

power grid is within

the normal range.

3. Replace the

compressor drive

board if it is faulty.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды