Huawei NetCol8000-A013 Скачать руководство пользователя страница 89

Страница: 89 / 181

Cate

gory

Sympto

Possible Cause

Measure

Out

door

unit

Abnorma

l noise is

generate

d during

operation

The compressor, fan, or

pipes are loose.

Check and secure loose parts.

The

compress

or does

not work.

The high and low pressure

switches are triggered.

Check the high and low pressure switches.

The switch or cable is

disconnected.

Check the main switch and cables.

The compressor is

damaged.

Replace the compressor.

The compressor does not

need to start.

Check for the temperature and humidity set

points on the LCD, and adjust the set points for

appropriate valve.

The main board or drive

board of outdoor unit is

damaged.

Replace the main board or drive board of

outdoor unit.

The

compress

discharge

temperat

ure is too

high.

The outdoor units are not

installed in right positions.

(The installation distances

should meet requirements.)

Install outdoor units in the right positions based

on the installation requirements.

Air enters the refrigerant

loop.

Check the discharge temperature and pressure.

Eliminate and retrieve refrigerant. Refill

refrigerant.

Heat dissipation is poor

because the condenser is

dirty or blocked.

Clean the condenser fins using a fin brush.

The outdoor fan fails.

Check whether the outdoor fan works properly.

The refrigerant is

insufficient.

Fill more refrigerant.

The

compress

discharge

pressure

is too

low.

The refrigerant is

insufficient.

Fill more refrigerant.

The outdoor fan speed

controller fails.

Replace the fan speed controller.

Refrigerant leaks.

Apply soapy water or use a halogen leak

detector to check for any leakage. If leaking

points are found, retrieve the refrigerant and

weld the leaking points again. Contact Huawei

technical support.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды