Huawei NetCol8000-A013 Скачать руководство пользователя страница 86

Страница: 86 / 181

Quarterly Preventive Maintenance Table

Table 5-2 Quarterly preventive maintenance table (on the basis of monthly preventive

maintenance)

Maintenance Item

Expected Result

Troubleshooting

Indoor fan

Check that the operating indoor fan

generates no abnormal noise.

Replace the fan component if it is

damaged.

Check that the screws on the indoor

fan are not loose or distorted.

Tighten loose screws.

Compressor

Check that the compressor is

secured.

Tighten screws if the compressor is

not secured.

Check that the operating compressor

generates no abnormal noise.

Replace the compressor.

Electric heater

The electric heaters are secured.

Secure the electric heaters and

temperature switches.

Check that the electric heater

surfaces are not eroded.

Replace the electric heater.

Outdoor fan

Check that the fan air intake and

exhaust vents are not blocked.

Clear obstacles.

Check that the fan runs properly

without abnormal noise or vibration,

and the blades rotate properly.

Replace the outdoor fan.

Yearly Preventive Maintenance Table

Table 5-3 Yearly preventive maintenance table (on the basis of quarterly preventive maintenance)

Maintenance Item

Expected Result

Troubleshooting

Monitoring unit

Export smart cooling product logs,

alarms, temperature, humidity, the

operating status of the compressor,

fan, electric heater, wet film

humidifier, and time. View the

historical alarms generated in this

year and select the most common

five ones.

Rectify the fault or contact Huawei

technical support.

Electric control box

components

Check that the electrical components

and control components of the

indoor unit are free of dust.

(Perform the operation with the

power off.) Use a brush or

compressed dry air to remove dust

from electrical components, and

control components.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды