Huawei NetCol8000-A013 Скачать руководство пользователя страница 37

Страница: 37 / 181

Temperatur

e (°C)

Saturation

Pressure-

Surface

Pressure

(MPa)

Temperatu

re (°C)

Saturation

Pressure-

Surface

Pressure

(MPa)

Temperatu

re (°C)

Saturatio

Pressure-

Surface

Pressure

(MPa)

0.9

1.60

2.63

0.93

1.65

2.7

0.96

1.69

2.76

0.99

1.74

2.83

1.02

1.79

2.9

1.05

1.84

2.97

1.09

1.89

3.04

1.12

1.94

3.11

1.16

1.99

3.19

1.19

2.04

3.26

1.23

2.1

3.34

1.27

2.15

–

3.2.2 (Optional) Refrigerant Oil RB75EA

The refrigerant oil is RB75EA. A sufficient amount of refrigerant oil has been filled

in the indoor compressor before delivery to ensure the reliable running of a 60 m

long pipe. Additional refrigerant oil is not required during onsite installation. When

the compressor is damaged, refrigerant oil has been filled in the compressor

before the compressor is replaced. Additional refrigerant oil is not required during

replacement. Add refrigerant oil based on the actual situation only when the

refrigerant oil leaks and the compressor does not need to be replaced.

3.2.3 Pipes

Oil Trap

Figure 3-2

shows the oil trap specifications.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

3 Installation Guide

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды