Huawei NetCol8000-A013 Скачать руководство пользователя страница 95

Страница: 95 / 181

Alarm

Alarm Name

System

Action

Possible Causes

Solution

207

Comp LP Switch

Alarm

The

compressor

shuts down.

1. The condenser fins

are dirty or blocked.

2. The indoor fan or its

drive is faulty.

3. The cables to the

low pressure switch

are loose or

damaged.

4. The low pressure

switch is faulty.

5. Refrigerant leaks.
6. The indoor unit is

not properly

installed.

7. The EEV is faulty.
8. The stop valve is

not fully open.

9. The filter is dirty or

blocked.

10.The selected model

is incorrect.

11.The connecting pipe

is bent.

1. Clean the condenser

fins.

2. Maintain or replace

the indoor fan drive

or indoor fan.

3. Check the cable

connections to the

low pressure switch.

4. Maintain or replace

the low pressure

switch.

5. Identify and repair

the leaking points,

and refill refrigerant

after maintenance.

6. Reinstall the indoor

unit.

7. Maintain or replace

the EEV coil or EEV.

8. Check and fully

open the stop valve.

9. Check and replace

the filter.

10.Check that the

selected model is

correct.

11.Check and replace

the connecting pipe.

208

Comp LP Switch

Lock Alarm

The

compressor

shuts down.

(The alarm

needs to be

manually

cleared.)

The Comp LP Switch

Alarm is triggered

multiple times within a

specified period of

time.

Refer to the solution to

the Comp LP Switch

Alarm.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды