Huawei NetCol8000-A013 Скачать руководство пользователя страница 102

Страница: 102 / 181

Alarm

Alarm Name

System

Action

Possible Causes

Solution

301

EEV Low

Superheat Degree

Alarm

The

compressor

shuts down.

1. The EEV is faulty or

its step is incorrect.

2. The cables to the

EEV are not properly

connected.

3. The EEV coil is

loose.

4. The plug of the EEV

is loose.

5. The plug of the EEV

is short-circuited.

6. The outdoor

temperature sensor

displays an incorrect

temperature or is

faulty.

1. Check and replace

the EEV.

2. Check and replace

the EEV body.

3. Secure the EEV coil.
4. Secure the plug.
5. Eliminate the short-

circuit fault.

6. Adjust or replace

the outdoor

temperature sensor.

302

EEV Low

Superheat Lock

Alarm

The

compressor

shuts down.

(The alarm

needs to be

manually

cleared.)

The EEV Low

Superheat Alarm is

triggered multiple

times within a

specified period of

time.

Refer to the solution to

the EEV Low Superheat

Alarm.

303

EEV Drive Alarm

The

compressor

shuts down.

1. The EEV is not

connected.

2. The EEV coil is

short-circuited.

3. The EEV drive circuit

of the indoor unit

main control board

is faulty.

1. Check the cables to

the EEV.

2. Check whether the

EEV coil is short-

circuited.

3. Replace the main

control board of the

indoor unit.

304

EEV Drive Lock

Alarm

The

compressor

shuts down.

The EEV Drive Alarm is

triggered multiple

times within a

specified period of

time.

Refer to the solution to

the EEV Drive Alarm.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды