Huawei NetCol8000-A013 Скачать руководство пользователя страница 80

Страница: 80 / 181

Table 4-5 Communication settings

Item

Description

Default Value

Baud Rate

Set the baud rate as

required. The value

should be consistent

with that set on the

NMS.

9600

Comm Address

The communications

address in one RS485

NMS must be unique,

which is irrelevant to the

cable connection

sequence or teamwork

address.

Enable Monitoring

Resistor

In an NMS, the values

for the first and last

smart cooling products

by cable routing are

"Yes".

----End

4.6 Commissioning Procedure

Context

●

Remove the refrigerant steel cylinder after confirming that sufficient

refrigerant has been injected.

●

If no electric heater or humidifier is configured, skip the commissioning

procedures for such components.

NO TICE

● The outdoor unit has been charged R410A refrigerant for 5 kg before delivery.

The indoor unit has been charged no refrigerant.

● If the R410A refrigerant is provided by Huawei, put the refrigerant cylinder

upside down when charging the refrigerant. If the refrigerant is not provided by

Huawei, check with the refrigerant provider whether the cylinder has a siphon.

If the cylinder has a siphon, stand the cylinder when charging refrigerant. If the

cylinder has no siphon, put the cylinder upside down when charging refrigerant.

These measures ensure that the refrigerant is charged in the liquid state.

Procedure

Step 1 Tap

to start the smart cooling product.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

4 Power-On Commissioning

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды