Huawei NetCol8000-A013 Скачать руководство пользователя страница 96

Страница: 96 / 181

Alarm

Alarm Name

System

Action

Possible Causes

Solution

209

Comp Discharge

HT Alarm

The

compressor

shuts down.

1. The condenser fins

are dirty or blocked.

2. The outdoor fan or

its drive is faulty.

3. The discharge

sensor is faulty.

4. Refrigerant leaks.
5. The outdoor unit is

not properly

installed.

6. The EEV is faulty.
7. The stop valve is

not fully open.

8. The filter is dirty or

blocked.

9. The connecting pipe

is bent.

1. Clean the condenser

fins.

2. Maintain or replace

the outdoor fan

drive or outdoor

fan.

3. Maintain or replace

the discharge

sensor.

4. Maintain or replace

the solenoid valve

coil or the solenoid

valve.

5. Identify and repair

the leaking points,

and refill refrigerant

after maintenance.

6. Reinstall the

outdoor unit.

7. Maintain or replace

the EEV coil or EEV.

8. Check and fully

open the stop valve.

9. Check and replace

the filter.

10.Check and replace

the connecting pipe.

210

Comp Discharge

HT Lock Alarm

The

compressor

shuts down.

(The alarm

needs to be

manually

cleared.)

The Comp Discharge

HT Alarm is triggered

multiple times within a

specified period of

time.

Refer to the solution to

the Comp Discharge

HT Alarm.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды