Huawei NetCol8000-A013 Скачать руководство пользователя страница 84

Страница: 84 / 181

System Operation and Maintenance

This chapter describes the operation and maintenance (O&M) for the NetCol8000-

A, including safety precautions, routine maintenance, alarm reference,

troubleshooting, and parts replacement.

5.1 Routine Maintenance

5.1.1 Routine Maintenance Overview

Definition

Routine maintenance refers to preventive and periodic check and maintenance

carried out to promptly identify and handle alarms and potential faults during the

normal operation of the equipment.

Precautions

●

Routine maintenance is critical to the normal operation of equipment.

Perform routine maintenance regularly. Read the precautions and product

documentation before performing routine maintenance.

●

Follow local laws and safety instructions to minimize the risk of personal

injury and damage to equipment.

●

The "NOTICE", "CAUTION", "WARNING", and "DANGER" statements in this

document do not represent all safety instructions. They are only supplements

to the safety instructions.

●

Personnel who will install, operate, and maintain Huawei equipment must

receive thorough training, understand all necessary safety precautions, and be

able to correctly perform all operations.

●

Pay attention to the safety symbols on the equipment and all safety

instructions in this document. The safety precautions given in this document

do not cover all safety precautions. Huawei will not be liable for any

consequence caused by violation of the safety operation regulations and

design, production, and usage standards.

●

Most maintenance tasks should be performed only after the power supply is

disconnected from the equipment. Do not connect the power supply during

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды