Huawei NetCol8000-A013 Скачать руководство пользователя страница 66

Страница: 66 / 181

3.14 Verifying the Installation

Table 3-9 Check items

Item

Check That

Check Result

Refrigerant

pipe

Ports are connected properly. The pipeline

has oil traps, gradients (for the refrigerant

pipes), and pipe supports. Pipes are

securely connected. All pipes and stop

valves are wrapped with thermal

insulation foam, and the insulation foam

is intact. The needle valve plug is secured

(torque of 0.45±0.05 N·m), and the valve

bonnet is tightened. The pipes have no

sharp bends.

□ Passed. □ Failed

Waterway

Water pipe joints have been sealed. The

drainpipe is securely connected.

□ Passed. □ Failed

Electricity

The power cables and signal cables are

connected as required. Indoor and

outdoor units are properly grounded.

Cables are not damaged or over-bent. The

rated specifications of the upstream

switch meet the maximum current

requirement.

□ Passed. □ Failed

Cabinet

The cabinet is installed properly, without

any tilt. The cabinet is secured. The

foreign matter inside the cabinet such as

cable ties and cable cuts is cleaned up.

□ Passed. □ Failed

Wet film

humidifier

The humidifier water inlet pipe is properly

connected and secured.

□ Passed. □ Failed

Water pan

The foreign matter inside the water pan is

cleaned up.

□ Passed. □ Failed

Air filter

The air filters have been installed.

□ Passed. □ Failed

Fan

The fan is secured. The fan has no foreign

matter inside.

□ Passed. □ Failed

Outdoor unit The fan blades do not interfere. Cables

are protected by tubes and the cable

outlet faces downward. The protective

cardboard of condenser fin has been

removed.

□ Passed. □ Failed

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

3 Installation Guide

Issue 02 (2020-11-09)

Содержание NetCol8000-A013






















































































































































































Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды

Huawei NetCol8000-A013, Руководство пользователя

Результаты поиска

Содержание NetCol8000-A013

Отзывы:

Похожие инструкции для NetCol8000-A013

Бренды по названию

Популярные бренды