Huawei NetCol5000-C030H90D0 страница 63 Скачать руководство пользователя

Страница: 63 / 206

Figure 3-32 Water inlet pipe (NetCol5000-C030/C032)

NO TE

The other end is a reserved G 3/4 inch connector with inner screw threads. Connect the

other end to a rigid pipe based on site requirements.

Step 3 Route the water inlet pipe from the inside to the outside through the water inlet

hole at the bottom of the smart cooling product.

Step 4 Clean the engineering pipes before connecting the water inlet pipe to the engineer

pipe to avoid impurities entering into the humidifier.

Step 5 Connect the water inlet pipe to the engineer pipe and wrap the pipe with thermal

insulation foam.

----End

3.8.3 Connecting the Chilled Water Inlet and Outlet Pipes

Context

●

A Y-shaped strainer has been installed on the chilled water inlet.

●

Connect the water inlet and outlet pipes from the inside to the outside and

from the bottom to the top.

●

Water inlet and outlet pipes are connected using thread connectors.

●

Chilled water inlet and outlet pipes can be connected in two ways. Select one

based on site requirements.

3.8.3.1 Connecting Seamless Steel Pipes

Procedure

Step 1 Open the rear door and remove the air filter.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

3 Installation

Issue 03 (2020-08-30)

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды