Huawei NetCol5000-C030H90D0 Скачать руководство пользователя

Страница: 144 / 206

Alar

m ID

Alarm

Name

Alarm

Severi

Possible Cause

Solution

A080

CW valve

exceed

runtime

alarm

WARNI

The accumulated

runtime of the

chilled water valve

exceeds the alarm

threshold.

Maintain or replace the

chilled water valve and

clear the accumulated

runtime.

A090

Cond pump

1 exceed

runtime

alarm

WARNI

Condensate pump

runtime exceeds the

limit.

Maintain or replace the

condensate pump, and

clear the total runtime.

A091

Cold aisle

low

temperature

alarm

WARNI

1. The temperature

sensors or

temperature and

humidity sensors are

located in

inappropriate

positions.
2. The thermal load

power is low.
3. The ambient

temperature is

below the lower

threshold.
4. The low

temperature alarm

threshold is

inappropriate.
5. The value

detected by the

temperature sensor

or temperature and

humidity sensor is

different from the

actual value.
6. The air filters are

blocked.
7. The chilled water

valve is stuck or

faulty.

1. Adjust the positions

of the temperature

sensors or temperature

and humidity sensors.
2. Contact Huawei

technical support.
3. Measure the ambient

temperature. Check

whether other causes

exist if the alarm

persists in a long time

after startup.
4. Adjust the low

temperature alarm

threshold.
5. Calibrate or replace

the temperature sensor

or temperature and

humidity sensor.
6. Maintain or replace

the air filters.
7. Maintain or replace

the chilled water valve.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

6 System Operation and Maintenance

Issue 03 (2020-08-30)

136

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды