Huawei NetCol5000-C030H90D0 Скачать руководство пользователя страница 133

Страница: 133 / 206

No. Operation

Troubleshooting

Period

Result

Use a high-precision

humidity and

temperature sensor

to calibrate the

humidity and

temperature sensors

inside and outside

the cabinet.

If the temperature

deviation is greater than

1°C or humidity deviation is

greater than 5%, calibrate

or replace the humidity and

temperature sensor.

Semi-

annual

□Passed
□Failed

The heat exchanger

fins are not pushed

down.

Use a fin brush to organize

the fins that are pushed

down.

Semi-

annual

□Passed
□Failed

Check that the

thermal insulation

foam on the chilled

water pipe is intact.

Rewrap the thermal

insulation foam.

Semi-

annual

□Passed
□Failed

Check that the pipe

support is intact and

securely installed.

Secure the base.

Semi-

annual

□Passed
□Failed

Check that pipes do

not leak.

Close the water inlet stop

valve and repair leaks.

Semi-

annual

□Passed
□Failed

Check that the smart

cooling product

drainpipe is free from

leaks and blockages.

If the drainpipe leaks, repair

the leaks. If the drainpipe is

blocked, clear the blockage

inside the pipe.

Semi-

annual

□Passed
□Failed

6.2 Alarm References

Table 6-2 Alarm list

Alar

m ID

Alarm

Name

Alarm

Severi

Possible Cause

Solution

A001

Return air 1

temperature

sensor fault

MAJO

1. The cables to the

temperature sensor

are loose or

damaged.
2. The temperature

sensor is faulty.

1. Check the cables to

the temperature sensor.
2. Maintain or replace

the temperature sensor.

Supply air 1

temperature

sensor fault

Supply air 2

temperature

sensor fault

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

6 System Operation and Maintenance

Issue 03 (2020-08-30)

125

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Бренды по названию

Популярные бренды