Huawei NetCol5000-C030H90D0 страница 132 Скачать руководство пользователя

Страница: 132 / 206

No. Operation

Troubleshooting

Period

Result

Choose Maint >

Diagnostic Mode >

Enter, and set the

chilled water valve

opening to 100%.

Check that the chilled

water valve handle

automatically turns

to the maximum

opening.

If the handle of the chilled

water valve actuator does

not automatically turn to

the maximum, adjust the

actuator to the maximum

(100 %).

Quarterl

□Passed
□Failed

Check that no foreign

matter exists in the

fan.

Clean the foreign matters.

Semi-

annual

□Passed
□Failed

Check that the fan

blades are intact.

Repair the fan blades. If the

fan blades are irreparable,

replace the fan.

Semi-

annual

□Passed
□Failed

Check that no

abnormal voice is

generated during

operation.

Clean the foreign matters,

and make sure that the fan

is fixed properly.

Semi-

annual

□Passed
□Failed

Check that the fan

screws are secured

and not deformed.

Tighten the screws. Replace

the screws if necessary.

Semi-

annual

□Passed
□Failed

Check that the wiring

terminals are

secured.

Reconnect the cables again. Semi-

annual

□Passed
□Failed

Check that the wiring

terminals are

secured.

If a wiring terminal is loose,

secure or replace it

promptly.

Semi-

annual

□Passed
□Failed

Use a brush or

compressed dry air to

clean various electric

components, control

components, the

main control board,

and so on.

N/A

Semi-

annual

□Passed
□Failed

Check whether the

display panel,

humidity and

temperature sensor

or cables is aging on

the surface.

Replace the components or

cables.

Semi-

annual

□Passed
□Failed

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

6 System Operation and Maintenance

Issue 03 (2020-08-30)

124

Содержание NetCol5000-C030H90D0















































































































































































































Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды

Huawei NetCol5000-C030H90D0, Руководство пользователя

Результаты поиска

Содержание NetCol5000-C030H90D0

Отзывы:

Похожие инструкции для NetCol5000-C030H90D0

Бренды по названию

Популярные бренды