manualshive.com logo in svg

Huawei NetCol5000-C030H90D0, Руководство пользователя

Поделиться
Скачать
Huawei NetCol5000-C030H90D0 Скачать руководство пользователя страница 155

Symptom

Possible Causes

Troubleshooting

Condensate

water exists on

the surfaces of

the front or rear

panels.

1. The operating

environment of the

NetCol5000-C is

excessively humid.

2. The temperature set

point is set to a much

smaller value.

1. Enhance the airtightness of

the equipment room.

2. Adjust the temperature and

humidity set points.

No water is

supplied to the

water inlet

solenoid valve of

the humidifier.

1. The upstream water

supply is faulty or the

water pressure is below

the lower threshold.

2. The water inlet

solenoid valve is

blocked or faulty.

3. The cable to the water

inlet solenoid valve is

incorrectly connected.

1. Restore the water supply.
2. Replace the water inlet

solenoid valve.

3. Reconnect the cable.

 

6.4 Parts Replacement

6.4.1 Replacement Requirements

NO TICE

● Before removing or installing the power cable, turn off the power switch.
● Before connecting a power cable, check that the label on the power cable is

correct.

● During the installation of AC power supply facilities, follow the local safety

regulations.

● When operating the high-voltage and AC-powered facilities, use dedicated

tools.

● Ensure that a spare component is the same model as the faulty one is prepared

before replacing the faulty component.

● Do not install or remove power cables when the device is on. Transient contact

between the core of the power cable and the conductor may generate electric

arcs or sparks, which may cause fire or hurt eyes.

● Before removing cables from a faulty component, mark the cables with their

corresponding ports numbers for later connection (confirm by referring to the

electrical conceptual diagram).

● Ensure that the cables are connected to the spare component properly.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

6 System Operation and Maintenance

Issue 03 (2020-08-30)

Copyright © Huawei Technologies Co., Ltd.

147

Содержание NetCol5000-C030H90D0















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды